POK POKETONE™ M330F

349

Properties:
High mobility
High impact resistance
High chemical resistance
High wear resistance
High gas barrier
High flame retardancy
Usages:
automobile
Electronic appliances
Industrial materials
Certificates:
TDS
MSDS
Compare
View Prices

Technical Data Sheet

physical property	Test Condition	Test Method	Test Result
Shore hardness		ISO 868	77
Rockwell hardness		ASTM D785	110
Water absorption rate		ASTM D570	0.5 %
saturation		ASTM D570	2.1 %
melt mass-flow rate		ASTM D1238	60 g/10min
melt mass-flow rate	melt mass-flow rate		ISO 1133	56
Shrinkage rate		ASTM D955	2 %
	Shrinkage rate		ASTM D955	2 %
		Shrinkage rate		ASTM D955	1.6 %
		Shrinkage rate	Shrinkage rate		ASTM D955	1.5 %

Mechanical properties	Test Condition	Test Method	Test Result
tensile strength		ASTM D638	60 Mpa
Tensile modulus		ASTM D638	1600 Mpa
Tensile modulus	Tensile modulus		ISO 527-1	1500 Mpa
elongation at yield		ASTM D638	21 %
elongation at break		ASTM D638	300 %
bending strength		ASTM D790	57 Mpa
Flexural modulus		ASTM D790	1500
Flexural modulus	Flexural modulus		ISO 178	1400

Impact resistance	Test Condition	Test Method	Test Result
Suspended wall beam without notch impact strength		ASTM D256	N.B.
Impact strength of cantilever beam gap		ASTM D256	95 kJ/m²
	Impact strength of cantilever beam gap		ISO 180/1A	7 kJ/m²
		Impact strength of cantilever beam gap		ASTM D256	60 kJ/m²
			Impact strength of cantilever beam gap		ISO 180/1A	4 kJ/m²
				Impact strength of cantilever beam gap		ASTM D256	40 kJ/m²
				Impact strength of cantilever beam gap	Impact strength of cantilever beam gap		ISO 180/1A	3 kJ/m²
Dart impact		ISO 6603-2	50 J

Electrical performance	Test Condition	Test Method	Test Result
dielectric strength		ASTM D149	15 KV/mm
dielectric strength	dielectric strength		ASTM D149	19 KV/mm
Volume resistivity		ASTM D257	1000000000000000 ohms·cm
Surface Resistivity		ASTM D257	1000000000000000000 ohm/sq
arc resistance		ASTM D495	130 sec
Compared to the Leakage Tracking Index (CTI)		IEC 112	V
dielectric constant		ASTM D150	6.2
dielectric constant	dielectric constant		IEC 250	5
Dissipation Factor		ASTM D150	0.008
Dissipation Factor	Dissipation Factor		IEC 250	0.013

Thermal performance	Test Condition	Test Method	Test Result
melting temperature		ASTM D955	222 °C
Linear coefficient of thermal expansion		ASTM E831	0.000097
vicat		ASTM D-1525	195 °C
vicat	vicat		ISO 306/B50	190 °C
Heat distortion temperature		ASTM D648	200 °C
	Heat distortion temperature		ASTM D648	105 °C
		Heat distortion temperature		ISO 75	190 °C
		Heat distortion temperature	Heat distortion temperature		ISO 75	92 °C

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

POK POKETONE™ M330F

Technical Data Sheet

You May Like