Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTM D1238 | 18 g/10 min |
| Shrinkage rate | | 内部方法 | 0.50 - 0.70 % |
| Water absorption rate | | ASTM D570 | 0.25 % |
| Water absorption rate | | ASTM D570 | 1.3 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 109 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | 5VA |
| Limiting Oxygen Index | | ASTM D2863 | 44 % |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 3580 Mpa |
| tensile strength | | ASTM D638 | 110 Mpa |
| elongation | | ASTM D638 | 7.0 % |
| elongation | | ASTM D638 | 60 % |
| Flexural modulus | | ASTM D790 | 3510 Mpa |
| bending strength | | ASTM D790 | 165 Mpa |
| Taber abraser | | ASTM D1044 | 10.0 mg |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Suspended wall beam without notch impact strength | | ASTM D4812 | 1300 J/m |
| Reverse notch impact | | ASTM D256 | 1500 J/m |
| Dart impact | | ASTM D3029 | 33.0 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Volume resistivity | | ASTM D257 | 1.0E+17 ohms·cm |
| dielectric strength | | ASTM D149 | 33 KV/mm |
| dielectric strength | | ASTM D149 | 28 KV/mm |
| dielectric constant | | ASTM D150 | 3.15 |
| Dissipation Factor | | ASTM D150 | 1.3E-3 |
| Dissipation Factor | | ASTM D150 | 2.5E-3 |
| arc resistance | | ASTM D495 | PLC 5 |
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 4 |
| High arc combustion index (HAI) | | UL 746 | PLC 3 |
| High Voltage Arc Traceability Rate (HVTR) | | UL 746 | PLC 2 |
| Hot wire ignition (HWI) | | UL 746 | PLC 1 |
| injection | Test Condition | Test Method | Test Result |
|---|
| drying temperature | | | 150 °C |
| drying time | | | 4.0 to 6.0 hr |
| Suggested maximum moisture content | | | 0.020 % |
| Suggested injection volume | | | 40 to 60 % |
| Temperature at the rear of the barrel | | | 330 to 400 °C |
| Temperature in the middle of the barrel | | | 340 to 400 °C |
| Temperature at the front of the material cylinder | | | 345 to 400 °C |
| Spray nozzle temperature | | | 345 to 400 °C |
| Processing (melt) temperature | | | 350 to 400 °C |
| Temperature | | | 135 to 165 °C |
| Back pressure | | | 0.300 to 0.700 Mpa |
| screw speed | | | 40 to 70 rpm |
| Exhaust hole depth | | | 0.025 to 0.076 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 207 °C |
| Heat distortion temperature | | ASTM D648 | 198 °C |
| vicat | | ASTM D15255 | 218 °C |
| Linear coefficient of thermal expansion | | ASTM E831 | 5.6E-5 cm/cm/°C |
| thermal conductivity | | ASTM C177 | 0.22 W/m/K |
| RTI Elec | | UL 746 | 170 °C |
| RTI Imp | | UL 746 | 170 °C |
| RTI | | UL 746 | 170 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices