PC Makrolon® 1239
62
- Properties:high viscosity
- Usages:filmElectronic fieldElectrical fieldBlow molding applicationsbottle
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Water absorption rate | ISO 62 | 0.30 % | |
| ISO 62 | 0.12 % | ||
| Shrinkage rate | ISO 294-4 | 0.80 % | |
| ISO 294-4 | 0.75 % | ||
| melt mass-flow rate | ISO 1133 | 2.5 g/10min | |
| density | ISO 1183 | 1.20 g/cm³ | |
| Apparent density | ISO 60 | 0.66 g/cm³ | |
| Melt volume flow rate | ISO 1133 | 2.00 cm3/10min |
| hardness | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ball-indentation hardness | ISO 2039-1 | 108 Mpa |
| optical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| refractive index | ISO 489 | 1.587 | |
| Haze ratio | ISO 14782 | <0.80 % | |
| transmissivity | ISO 13468-2 | 88.0 % | |
| ISO 13468-2 | 87.0 % | ||
| ISO 13468-2 | 84.0 % |
| flammability | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Limiting Oxygen Index | ISO 4589-2 | 26 % | |
| Burning wire flammability index | IEC 60695-2-12 | 900 °C | |
| IEC 60695-2-12 | 900 °C | ||
| IEC 60695-2-12 | 930 °C | ||
| Hot filament ignition temperature | IEC 60695-2-13 | 900 °C | |
| IEC 60695-2-13 | 900 °C | ||
| IEC 60695-2-13 | 900 °C | ||
| FlashIgnitionTemperature | ASTM D1929 | 480 °C | |
| SelfIgnitionTemperature | ASTM D1929 | 550 °C |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Impact strength of simply supported beam without notch | ISO 179/1eU | NoBreak | |
| ISO 179/1eU | NoBreak | ||
| ISO 179/1eU | NoBreak | ||
| Charpy Notched Impact Strength | ISO 7391 | 75 kJ/m² | |
| ISO 7391 | 20 kJ/m² | ||
| Impact strength of cantilever beam gap | ISO 7391 | 55 kJ/m² | |
| ISO 7391 | 65 kJ/m² | ||
| Multi axis Instrumented Impact Energy | ISO 6603-2 | 55.0 J | |
| ISO 6603-2 | 60.0 J | ||
| Multi axis Instrumented Peak Impact Force | ISO 6603-2 | 6400 N | |
| ISO 6603-2 | 5500 N |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Nominal tensile fracture strain | ISO 527-2/50 | >50 % | |
| Tensile strain | ISO 527-2/50 | 6.6 % | |
| ISO 527-2/50 | 100 % | ||
| Bending Strain | ISO 178 | 7.2 % | |
| Tensile modulus | ISO 527-2/1 | 2300 Mpa | |
| Flexural modulus | ISO 178 | 2300 Mpa | |
| bending strength | ISO 178 | 70.0 Mpa | |
| ISO 178 | 94.0 Mpa | ||
| tensile strength | ISO 527-2/50 | 64.0 Mpa | |
| ISO 527-2/50 | 65.0 Mpa |
| film | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Water Vapor Transmission Rate | ISO 15106-1 | 15 g/m²/24hr | |
| GasPermeation | ISO 2556 | 4200 cm³/m²/bar/24hr | |
| ISO 2556 | 140 cm³/m²/bar/24hr | ||
| ISO 2556 | 740 cm³/m²/bar/24hr |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Dissipation Factor | IEC 60250 | 1E-03 | |
| IEC 60250 | 0.010 | ||
| relative permittivity | IEC 60250 | 3.10 | |
| IEC 60250 | 3.00 | ||
| Surface Resistivity | IEC 60093 | 1E+16 ohms | |
| Volume resistivity | IEC 60093 | 1E+16 ohms·cm | |
| dielectric strength | IEC 60243-1 | 34 KV/mm | |
| Compared to the Leakage Tracking Index (CTI) | IEC 60112 | V | |
| IEC 60112 | V |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ball-indentation hardness | IEC 60695-10-2 | Pass | |
| Heat distortion temperature | ISO 75-2/B | 145 °C | |
| ISO 75-2/A | 132 °C | ||
| vicat | ISO 306/B50 | 150 °C | |
| Glass Transition Temperature | ISO 11357-2 | 152 °C | |
| vicat | ISO 306/B120 | 151 °C | |
| Linear coefficient of thermal expansion | ISO 11359-2 | 7E-05 cm/cm/°C | |
| ISO 11359-2 | 7E-05 cm/cm/°C | ||
| thermal conductivity | ISO 8302 | 0.20 W/m/K |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
You May Like
Contact Us
Get App
Top