PC LEXAN™ EXL9132
36
- Properties:High mobilityDuctility at low temperatShort molding cycle
- Usages:Electronic and Electrical ApplicationsAerospace Applications
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|---|---|---|
| density | ASTMD792 | 1.18 g/cm³ | |
| ISO1183 | 1.19 g/cm³ | ||
| melt mass-flow rate | ASTMD1238 | 17 g/10min | |
| Melt volume flow rate | ISO1133 | 16.0 cm3/10min | |
| Shrinkage rate | 内部方法 | 0.40to0.80 % | |
| 内部方法 | 0.40to0.80 % | ||
| Water absorption rate | ISO62 | 0.35 % | |
| ISO62 | 0.15 % |
| hardness | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ISO2039-1 | 95.0 Mpa |
| flammability | Test Condition | Test Method | Test Result |
|---|---|---|---|
| UL flame retardant rating | UL94 | V-0 | |
| UL94 | 5VA | ||
| Burning wire flammability index | IEC60695-2-12 | 960 °C | |
| Hot filament ignition temperature | IEC60695-2-13 | 825 °C | |
| Limiting Oxygen Index | ISO4589-2 | 40 % |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|---|---|---|
| elongation | ASTMD638 | 5.8 % | |
| Tensile strain | ISO527-2/50 | 5.0 % | |
| elongation | ASTMD638 | 100 % | |
| Tensile strain | ISO527-2/50 | 100 % | |
| Flexural modulus | ASTMD790 | 2340 Mpa | |
| ISO178 | 2300 Mpa | ||
| Bending strength 5,6 | ISO178 | 88.0 Mpa | |
| bending strength | ASTMD790 | 95.1 Mpa | |
| Tensile modulus | ASTMD638 | 2270 Mpa | |
| ISO527-2/1 | 2200 Mpa | ||
| tensile strength | ASTMD638 | 58.1 Mpa | |
| Tensile stress | ISO527-2/50 | 59.0 Mpa | |
| tensile strength | ASTMD638 | 58.5 Mpa | |
| Tensile stress | ISO527-2/50 | 55.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Impact strength of simply supported beam gap 7 | ISO179/1eA | 25 kJ/m² | |
| ISO179/1eA | 60 kJ/m² | ||
| The impact strength of a simply supported beam without a notch is 7 | ISO179/1eU | NoBreak | |
| ISO179/1eU | NoBreak | ||
| Impact strength of cantilever beam gap | ASTMD256 | 560 J/m | |
| ASTMD256 | 730 J/m | ||
| ISO180/1A | 20 kJ/m² | ||
| ISO180/1A | 55 kJ/m² | ||
| Unscented Izod Impact Strength 8 | ISO180/1U | NoBreak | |
| ISO180/1U | NoBreak | ||
| Dart impact equipped with measuring instruments | ASTMD3763 | 67.9 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| dielectric strength | IEC60243-1 | 19 KV/mm | |
| IEC60250 | 2.70 | ||
| IEC60250 | 2.70 | ||
| IEC60250 | 2.70 | ||
| Dissipation Factor | IEC60250 | 4E-04 | |
| IEC60250 | 4E-04 | ||
| IEC60250 | 0.010 | ||
| CTI | IEC60112 | 175 V |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ASTME831 | 7.2E-05 cm/cm/°C | ||
| ISO11359-2 | 7.5E-05 cm/cm/°C | ||
| RTI Elec | UL746 | 130 °C | |
| RTI Imp | UL746 | 50.0 °C | |
| RTI Str | UL746 | 50.0 °C | |
| ASTMD648 | 136 °C | ||
| Hot deformation temperature 9 | ISO75-2/Be | 136 °C | |
| ASTMD648 | 124 °C | ||
| Hot deformation temperature 9 | ISO75-2/Ae | 124 °C | |
| vicat | ASTMD152510 | 143 °C | |
| ISO306/B50 | 143 °C | ||
| ISO306/B120 | 144 °C | ||
| BallPressure Test | IEC60695-10-2 | Pass | |
| ASTME831 | 7.2E-05 cm/cm/°C | ||
| ISO11359-2 | 7.5E-05 cm/cm/°C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Contact Us
Get App
Top