Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| density | | ASTMD792 | 1.24 g/cm³ |
| density | | ISO1183 | 1.24 g/cm³ |
| Outdoor applicability | | UL746C | f1 |
| melt mass-flow rate | | ASTMD1238 | 8.0 g/10min |
| Melt volume flow rate | | ISO1133 | 7.00 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.40to0.80 % |
| Shrinkage rate | | 内部方法 | 0.40to0.80 % |
| Water absorption rate | | ISO62 | 0.12 % |
| Water absorption rate | | ISO62 | 0.050 % |
| Outdoor applicability | | UL746C | f1 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL94 | 5VA |
| GlowWireFlammability Index | | IEC60695-2-12 | 960 °C |
| Hot filament ignition temperature | | IEC60695-2-13 | 900 °C |
| UL flame retardant rating | | UL94 | V-0 |
| UL flame retardant rating | | UL94 | 5VB |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Flexural modulus | | ISO178 | 2150 Mpa |
| Tensile modulus | | ASTMD638 | 2150 Mpa |
| Tensile modulus | | ISO527-2/1 | 2150 Mpa |
| Bending strength 5,6 | | ISO178 | 86.0 Mpa |
| tensile strength | | ASTMD638 | 59.0 Mpa |
| Tensile stress | | ISO527-2/50 | 59.0 Mpa |
| tensile strength | | ASTMD638 | 58.0 Mpa |
| Tensile stress | | ISO527-2/50 | 58.0 Mpa |
| elongation | | ASTMD638 | 6.0 % |
| Tensile strain | | ISO527-2/50 | 6.0 % |
| elongation | | ASTMD638 | 100 % |
| Tensile strain | | ISO527-2/50 | 100 % |
| Flexural modulus | | ASTMD790 | 2150 Mpa |
| Flexural modulus | | ISO178 | 2150 Mpa |
| Tensile modulus | | ASTMD638 | 2150 Mpa |
| Tensile modulus | | ISO527-2/1 | 2150 Mpa |
| Bending strength 5,6 | | ISO178 | 86.0 Mpa |
| bending strength | | ASTMD790 | 86.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam gap 7 | | ISO179/1eA | 50 kJ/m² |
| Impact strength of simply supported beam gap 7 | | ISO179/1eA | 70 kJ/m² |
| The impact strength of a simply supported beam without a notch is 7 | | ISO179/1eU | NoBreak |
| The impact strength of a simply supported beam without a notch is 7 | | ISO179/1eU | NoBreak |
| Impact strength of cantilever beam gap | | ISO180/1A | 50 kJ/m² |
| Impact strength of cantilever beam gap | | ISO180/1A | 75 kJ/m² |
| Unscented Izod Impact Strength 8 | | ISO180/1U | NoBreak |
| Unscented Izod Impact Strength 8 | | ISO180/1U | NoBreak |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| CTI | | IEC60112 | 250 V |
| Compared to the Leakage Tracking Index (CTI) | | UL746 | PLC 2 |
| CTI | | IEC60112 | 250 V |
| High arc combustion index (HAI) | | UL746 | PLC 0 |
| Hot wire ignition (HWI) | | UL746 | PLC 2 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| RTI Elec | | UL746 | 125 °C |
| RTI Imp | | UL746 | 110 °C |
| RTI Str | | UL746 | 125 °C |
| vicat | | ASTMD152511 | 147 °C |
| BallPressure Test | | IEC60695-10-2 | Pass |
| RTI Elec | | UL746 | 125 °C |
| RTI Imp | | UL746 | 110 °C |
| RTI Str | | UL746 | 125 °C |
| Heat distortion temperature | | ASTMD648 | 139 °C |
| Hot deformation temperature 9 | | ISO75-2/Be | 139 °C |
| Heat distortion temperature | | ASTMD648 | 126 °C |
| Hot deformation temperature 10 | | ISO75-2/Af | 126 °C |
| vicat | | ASTMD152511 | 147 °C |
| vicat | | ISO306/B50 | 145 °C |
| vicat | | ISO306/B120 | 147 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare