Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTMD1238 | 13 g/10min |
| Melt volume flow rate | | ISO1133 | 12.0 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.50到0.70 % |
| Shrinkage rate | | 内部方法 | 0.50到0.70 % |
| Water absorption rate | | ISO62 | 0.35 % |
| Water absorption rate | | ISO62 | 0.15 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| | ISO2039-1 | 95.0 Mpa |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| refractive index | | ISO489 | 1.586 |
| transmissivity | | ASTMD1003 | 89.0 % |
| Haze ratio | | ASTMD1003 | <0.80 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| Burning wire flammability index | | IEC60695-2-12 | 850 °C |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| tensile strength | | ASTMD638 | 62.0 Mpa |
| tensile strength | | ISO527-2/50 | 63.0 Mpa |
| tensile strength | | ASTMD638 | 69.0 Mpa |
| tensile strength | | ISO527-2/50 | 70.0 Mpa |
| elongation | | ASTMD638 | 7.0 % |
| elongation | | ISO527-2/50 | 6.0 % |
| elongation | | ASTMD638 | 130 % |
| elongation | | ISO527-2/50 | 120 % |
| Flexural modulus | | ASTMD790 | 2340 Mpa |
| Flexural modulus | | ISO178 | 2300 Mpa |
| Bending stress | | ISO178 | 90.0 Mpa |
| Bending stress | | ASTMD790 | 97.0 Mpa |
| | 内部方法 | 10.0 mg |
| Tensile modulus | | ASTMD638 | 2300 Mpa |
| Tensile modulus | | ISO527-2/1 | 2350 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam gap 7 | | ISO179/1eA | 14 kJ/m² |
| Impact strength of simply supported beam gap 7 | | ISO179/1eA | 73 kJ/m² |
| The impact strength of a simply supported beam without a notch is 7 | | ISO179/1eU | 无断裂 |
| The impact strength of a simply supported beam without a notch is 7 | | ISO179/1eU | 无断裂 |
| Unscented Izod Impact Strength 8 | | ISO180/1U | 无断裂 |
| Unscented Izod Impact Strength 8 | | ISO180/1U | 无断裂 |
| Dart impact equipped with measuring instruments | | ASTMD3763 | 64.0 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | ASTMD257 | 5E+13 ohms |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| vicat | | ISO306/B120 | 141 °C |
| BallPressure Test | | IEC60695-10-2 | 通过 |
| | ASTME831 | 7E-05 cm/cm/°C |
| | ISO11359-2 | 7E-05 cm/cm/°C |
| | ASTME831 | 7E-05 cm/cm/°C |
| | ISO11359-2 | 7E-05 cm/cm/°C |
| thermal conductivity | | ISO8302 | 0.20 W/m/K |
| | ISO75-2/Be | 135 °C |
| | ASTMD648 | 114 °C |
| | ASTMD648 | 130 °C |
| | ISO75-2/Ae | 123 °C |
| vicat | | ASTMD152510 | 153 °C |
| vicat | | ISO306/B50 | 140 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare