Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTMD1238 | 25 g/10min |
| Melt volume flow rate | | ISO1133 | 23.2 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.50to0.70 % |
| Shrinkage rate | | 内部方法 | 0.50to0.70 % |
| Shrinkage rate | | 内部方法 | 0.50to0.70 % |
| Water absorption rate | | ISO62 | 0.35 % |
| Water absorption rate | | ISO62 | 0.15 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL94 | V-2 |
| UL flame retardant rating | | UL94 | V-0 |
| Burning wire flammability index | | IEC60695-2-12 | 960 °C |
| Hot filament ignition temperature | | IEC60695-2-13 | 800 °C |
| Limiting Oxygen Index | | ISO4589-2 | 36 % |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus 3 | | ASTMD638 | 2680 Mpa |
| Tensile modulus | | ISO527-2/1 | 2460 Mpa |
| Tensile strength 4 | | ASTMD638 | 63.4 Mpa |
| Tensile stress | | ISO527-2/50 | 64.8 Mpa |
| Tensile strength 4 | | ASTMD638 | 51.0 Mpa |
| Tensile stress | | ISO527-2/50 | 53.5 Mpa |
| elongation | | ASTMD638 | 4.8 % |
| Tensile strain | | ISO527-2/50 | 4.7 % |
| elongation | | ASTMD638 | 96 % |
| Tensile strain | | ISO527-2/50 | 97 % |
| Flexural modulus | | ASTMD790 | 2670 Mpa |
| Bending modulus 6 | | ISO178 | 2370 Mpa |
| Bending strength 6,7 | | ISO178 | 94.8 Mpa |
| Flexural Strength5 | | ASTMD790 | 102 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| CharpyNotchedImpactStrength8 | | ISO179/1eA | 18 kJ/m² |
| Suspended wall beam gap impact strength 9 | | ISO180/1A | 12 kJ/m² |
| Suspended wall beam gap impact strength 9 | | ISO180/1A | 18 kJ/m² |
| Dart impact equipped with measuring instruments | | ASTMD3763 | 48.6 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | IEC60093 | >1.0E+15 ohms |
| Volume resistivity | | IEC60093 | >1.0E+15 ohms·cm |
| dielectric strength | | ASTMD149 | 27 KV/mm |
| | IEC60250 | 3.00 |
| | IEC60250 | 3.00 |
| | IEC60250 | 2.90 |
| Dissipation Factor | | IEC60250 | 0.030 |
| Dissipation Factor | | IEC60250 | 0.030 |
| Dissipation Factor | | IEC60250 | 0.010 |
| CTI | | IEC60112 | 200 V |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| RTI Str | | UL746 | 80.0 °C |
| vicat | | ASTMD152511 | 111 °C |
| vicat | | ISO306/B50 | 113 °C |
| vicat | | ISO306/B120 | 114 °C |
| BallPressure Test | | IEC60695-10-2 | Pass |
| | ASTME831 | 7E-05 cm/cm/°C |
| | ISO11359-2 | 7E-05 cm/cm/°C |
| | ASTME831 | 7E-05 cm/cm/°C |
| | ISO11359-2 | 7E-05 cm/cm/°C |
| RTI Elec | | UL746 | 80.0 °C |
| RTI Imp | | UL746 | 80.0 °C |
| Heat distortion temperature | | ASTMD648 | 106 °C |
| Hot deformation temperature 10 | | ISO75-2/Af | 96.1 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare