Technical Data Sheet
physical property | Test Condition | Test Method | Test Result |
---|
melt mass-flow rate | | ASTM D1238 | 8.0 g/10min |
Melt volume flow rate | | ISO 1133 | 7.50 cm3/10min |
Shrinkage rate | | 内部方法 | 0.40-0.80 % |
Shrinkage rate | | 内部方法 | 0.40-0.80 % |
Water absorption rate | | ISO 62 | 0.35 % |
Water absorption rate | | ISO 62 | 0.15 % |
flammability | Test Condition | Test Method | Test Result |
---|
UL flame retardant rating | | UL 94 | HB |
Mechanical properties | Test Condition | Test Method | Test Result |
---|
elongation | | ISO 527-2/50 | 88 % |
Flexural modulus | | ASTM D790 | 2000 Mpa |
Flexural modulus | | ISO 178 | 2090 Mpa |
bending strength | | ISO 178 | 85.0 Mpa |
bending strength | | ASTM D790 | 79.3 Mpa |
Tensile modulus | | ASTM D638 | 1720 Mpa |
Tensile modulus | | ISO 527-2/1 | 2280 Mpa |
tensile strength | | ASTM D638 | 55.2 Mpa |
tensile strength | | ISO 527-2/50 | 54.0 Mpa |
tensile strength | | ASTM D638 | 60.0 Mpa |
tensile strength | | ISO 527-2/50 | 58.0 Mpa |
elongation | | ASTM D638 | 5.5 % |
elongation | | ISO 527-2/50 | 6.0 % |
elongation | | ASTM D638 | 100 % |
Impact resistance | Test Condition | Test Method | Test Result |
---|
Charpy Notched Impact Strength | | ISO 179/1eA | 60 kJ/m² |
Charpy Notched Impact Strength | | ISO 179/1eA | 70 kJ/m² |
Impact strength of simply supported beam without notch | | ISO 179/1eU | 无断裂 |
Impact strength of simply supported beam without notch | | ISO 179/1eU | 无断裂 |
Suspended wall beam without notch impact strength | | ASTM D4812 | 3200 J/m |
Suspended wall beam without notch impact strength | | ISO 180/1U | 无断裂 |
Suspended wall beam without notch impact strength | | ISO 180/1U | 无断裂 |
Dart impact | | ASTM D3763 | 61.0 J |
Dart impact | | ASTM D3763 | 62.1 J |
Electrical performance | Test Condition | Test Method | Test Result |
---|
High Voltage Arc Traceability Rate (HVTR) | | UL 746 | PLC 3 |
Hot wire ignition (HWI) | | UL 746 | PLC 2 |
Surface Resistivity | | IEC 60093 | 4.1E+17 ohms |
Volume resistivity | | IEC 60093 | 1.7E+17 ohms·cm |
dielectric strength | | IEC 60243-1 | 18 KV/mm |
relative permittivity | | IEC 60250 | 2.69 |
Dissipation Factor | | IEC 60250 | 9.4E-03 |
arc resistance | | ASTM D495 | PLC 5 |
Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 3 |
High arc combustion index (HAI) | | UL 746 | PLC 0 |
Thermal performance | Test Condition | Test Method | Test Result |
---|
RTI Imp | | UL 746 | 80.0 °C |
RTI | | UL 746 | 80.0 °C |
Heat distortion temperature | | ASTM D648 | 136 °C |
Heat distortion temperature | | ISO 75-2/Be | 136 °C |
Heat distortion temperature | | ASTM D648 | 122 °C |
Heat distortion temperature | | ISO 75-2/Ae | 122 °C |
vicat | | ASTMD152511 | 141 °C |
vicat | | ISO 306/B120 | 140 °C |
ball-indentation hardness | | IEC 60695-10-2 | 通过 |
Linear coefficient of thermal expansion | | ASTME831 | 7E-05 cm/cm/°C |
Linear coefficient of thermal expansion | | ISO 11359-2 | 6.9E-05 cm/cm/°C |
Linear coefficient of thermal expansion | | ASTME831 | 7.2E-05 cm/cm/°C |
Linear coefficient of thermal expansion | | ISO 11359-2 | 7.3E-05 cm/cm/°C |
RTI Elec | | UL 746 | 80.0 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.