Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Water absorption rate | | ISO 62 | 4.2 % |
| Water absorption rate | | ISO 62 | 1.2 % |
| density | | ASTMD792 | 1.08 g/cm³ |
| melt mass-flow rate | | ASTM D1238 | 15 g/10min |
| Melt volume flow rate | | ISO 1133 | 11.0 cm³/10min |
| Shrinkage rate | | 内部方法 | 1.2to1.6 % |
| Shrinkage rate | | 内部方法 | 1.2to1.6 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| Burning wire flammability index | | IEC 60695-2-12 | 650 °C |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 2000 MPa |
| Tensile modulus | | ISO 527-2/1 | 2100 MPa |
| tensile strength | | ASTM D638 | 55.0 MPa |
| tensile strength | Yield | ISO 527-2/50 | 55.0 MPa |
| tensile strength | | ASTM D638 | 50.0 MPa |
| tensile strength | Break | ISO 527-2/50 | 50.0 MPa |
| elongation | | ASTM D638 | 5.0 % |
| elongation | Yield | ISO 527-2/50 | 4.0 % |
| elongation | | ASTM D638 | 60 % |
| elongation | Break | ISO 527-2/50 | 30 % |
| Flexural modulus | | ASTM D790 | 2050 MPa |
| Flexural modulus | | ISO 178 | 2150 MPa |
| bending strength | | ISO 178 | 80.0 MPa |
| bending strength | | ASTM D790 | 80.0 MPa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ISO 179/1eA | 12 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179/1eA | 20 kJ/m² |
| Impact strength of cantilever beam gap | | ASTM D256 | 150 J/m |
| Impact strength of cantilever beam gap | | ASTM D256 | 220 J/m |
| Impact strength of cantilever beam gap | | ISO 180/1A | 7.0 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | 17 kJ/m² |
| Suspended wall beam without notch impact strength | | ISO 180/1U | 无断裂 |
| Suspended wall beam without notch impact strength | | ISO 180/1U | 无断裂 |
| Dart impact | | ASTM D3763 | 50.0 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Volume resistivity | | 内部方法 | 1.0E+3到1.0E+4 ohms·cm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Linear coefficient of thermal expansion | | ISO 11359-2 | 9.6E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTME831 | 1E-04 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 9.6E-05 cm/cm/°C |
| Heat distortion temperature | | ISO 75-2/Be | 178 °C |
| vicat | | ASTMD152511 | 180 °C |
| vicat | | ISO 306/B120 | 182 °C |
| Linear coefficient of thermal expansion | | ASTME831 | 9.5E-05 cm/cm/°C |
| Heat distortion temperature | | ASTM D648 | 185 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare