PC LEXAN™ EXL9330 GY4D167
31
- Properties:Flame retardantTougheningUV resistance
- Usages:CastersThin walled productsfood
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|---|---|---|
| melt mass-flow rate | ASTM D1238 | 10 g/10 min | |
| Molten Volume Flow Rate (MVR) | ISO 1133 | 9.00 cm3/10min | |
| Shrinkage rate | 内部方法 | 0.40 到 0.80 % | |
| 内部方法 | 0.40 到 0.80 % | ||
| Water absorption rate | ISO 62 | 0.35 % | |
| ISO 62 | 0.15 % | ||
| Outdoor applicability | UL 746C | f1 | |
| density | ASTM D792 | 1.18 g/cm³ | |
| ISO 1183 | 1.19 g/cm³ | ||
| Outdoor applicability | UL 746C | f1 |
| hardness | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ISO 2039-1 | 90.0 Mpa |
| flammability | Test Condition | Test Method | Test Result |
|---|---|---|---|
| UL flame retardant rating | UL 94 | V-0 | |
| UL 94 | 5VA | ||
| Burning wire flammability index | IEC 60695-2-12 | 960 °C | |
| Hot filament ignition temperature | IEC 60695-2-13 | 825 °C | |
| Limiting Oxygen Index | ISO 4589-2 | 35 % | |
| ISO 4589-2 | 35 % |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Tensile modulus | ASTM D638 | 2100 Mpa | |
| ISO 527-2/1 | 2100 Mpa | ||
| tensile strength | ASTM D638 | 58.0 Mpa | |
| ISO 527-2/50 | 55.0 Mpa | ||
| ASTM D638 | 61.0 Mpa | ||
| ISO 527-2/50 | 60.0 Mpa | ||
| elongation | ASTM D638 | 6.0 % | |
| ISO 527-2/50 | 6.0 % | ||
| ASTM D638 | 130 % | ||
| ISO 527-2/50 | 130 % | ||
| Flexural modulus | ASTM D790 | 2060 Mpa | |
| ISO 178 | 2200 Mpa | ||
| Bending stress | ISO 178 | 85.0 Mpa | |
| ASTM D790 | 88.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Impact strength of simply supported beam gap 7 | ISO 179/1eA | 60 kJ/m² | |
| ISO 179/1eA | 75 kJ/m² | ||
| The impact strength of a simply supported beam without a notch is 7 | ISO 179/1eU | 无断裂 | |
| ISO 179/1eU | 无断裂 | ||
| ISO 180/1U | 无断裂 | ||
| ISO 180/1U | 无断裂 | ||
| Dart impact equipped with measuring instruments | ASTM D3763 | 52.0 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Surface Resistivity | IEC 60093 | > 1.0E+15 ohms | |
| Volume resistivity | IEC 60093 | > 1.0E+15 ohms·cm | |
| dielectric strength | ASTM D149 | 17 KV/mm | |
| IEC 60243-1 | 16 KV/mm | ||
| dielectric constant | ASTM D150 | 2.95 | |
| ASTM D150 | 2.95 | ||
| ASTM D150 | 2.90 | ||
| IEC 60250 | 2.60 | ||
| IEC 60250 | 2.60 | ||
| IEC 60250 | 2.70 | ||
| Dissipation Factor | ASTM D150 | 2.4E-3 | |
| ASTM D150 | 2.4E-3 | ||
| ASTM D150, IEC 60250 | 8.5E-3 | ||
| IEC 60250 | 1.0E-3 | ||
| IEC 60250 | 1.0E-3 | ||
| Compared to the Leakage Tracking Index (CTI) | UL 746 | PLC 3 | |
| CTI | IEC 60112 | 225 V | |
| High arc combustion index (HAI) | UL 746 | PLC 0 | |
| Hot wire ignition (HWI) | UL 746 | PLC 1 | |
| Surface Resistivity | IEC 60093 | > 1.0E+15 ohms | |
| Volume resistivity | IEC 60093 | > 1.0E+15 ohms·cm | |
| Compared to the Leakage Tracking Index (CTI) | UL 746 | PLC 3 | |
| CTI | IEC 60112 | 225 V | |
| High arc combustion index (HAI) | UL 746 | PLC 0 | |
| Hot wire ignition (HWI) | UL 746 | PLC 1 |
| injection | Test Condition | Test Method | Test Result |
|---|---|---|---|
| drying temperature | 120 °C | ||
| drying time | 3.0 到 4.0 hr | ||
| Suggested maximum moisture content | 0.020 % | ||
| Suggested injection volume | 40 到 60 % | ||
| Temperature at the rear of the barrel | 215 到 295 °C | ||
| Temperature in the middle of the barrel | 280 到 305 °C | ||
| Temperature at the front of the material cylinder | 295 到 315 °C | ||
| Spray nozzle temperature | 290 到 310 °C | ||
| Processing (melt) temperature | 295 到 315 °C | ||
| Temperature | 70 到 95 °C | ||
| Back pressure | 0.300 到 0.700 Mpa | ||
| screw speed | 40 到 70 rpm | ||
| Exhaust hole depth | 0.025 到 0.076 mm | ||
| drying temperature | 120 °C | ||
| drying time | 3.0 到 4.0 hr | ||
| Suggested maximum moisture content | 0.020 % | ||
| Suggested injection volume | 40 到 60 % | ||
| Temperature at the rear of the barrel | 215 到 295 °C | ||
| Temperature in the middle of the barrel | 280 到 305 °C | ||
| Temperature at the front of the material cylinder | 295 到 315 °C | ||
| Spray nozzle temperature | 290 到 310 °C | ||
| Processing (melt) temperature | 295 到 315 °C | ||
| Temperature | 70 到 95 °C | ||
| Back pressure | 0.300 到 0.700 Mpa | ||
| screw speed | 40 到 70 rpm | ||
| Exhaust hole depth | 0.025 到 0.076 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Thermal deformation temperature under load | ASTM D648 | 134 °C | |
| ISO 75-2/Be | 135 °C | ||
| ASTM D648 | 120 °C | ||
| ASTM D648 | 124 °C | ||
| ISO 75-2/Ae | 124 °C | ||
| vicat | ASTM D152512, ISO 306/B12012 | 142 °C | |
| ISO 306/B50 | 140 °C | ||
| Ball Pressure Test | IEC 60695-10-2 | 通过 | |
| ASTM E831 | 6.7E-5 cm/cm/°C | ||
| ISO 11359-2 | 7.2E-5 cm/cm/°C | ||
| ASTM E831 | 6.7E-5 cm/cm/°C | ||
| ISO 11359-2 | 7.7E-5 cm/cm/°C | ||
| RTI Elec | UL 746 | 125 °C | |
| RTI Imp | UL 746 | 115 °C | |
| RTI | UL 746 | 125 °C | |
| RTI Elec | UL 746 | 125 °C | |
| RTI Imp | UL 746 | 115 °C | |
| RTI | UL 746 | 125 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Contact Us
Get App
Top