Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Water absorption rate | | ASTMD570 | 0.16 % |
| Water absorption rate | | ISO62 | 0.16 % |
| Water absorption rate | | ISO62 | 0.35 % |
| melt mass-flow rate | | ASTMD1238 | 30 g/10min |
| Melt volume flow rate | | ISO1133 | 29.0 cm³/10min |
| Shrinkage rate | | 内部方法 | 0.60to0.80 % |
| density | | ASTMD792 | 1.20 g/cm³ |
| Specific volume | | ASTMD792 | 0.830 cm³/g |
| density | | ASTMD792 | 1.19 g/cm³ |
| density | | ISO1183 | 1.20 g/cm³ |
| melt mass-flow rate | | ASTMD1238 | 6.0 g/10min |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTMD785 | 85 |
| Rockwell hardness | R-Scale | ASTMD785 | 122 |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| refractive index | | ASTMD542 | 1.600 |
| Haze ratio | | ASTMD1003 | 1.0 % |
| transmissivity | | ASTMD1003 | 85.0 % |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ISO179/1eA | 57 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO179/1eU | NoBreak |
| Impact strength of simply supported beam without notch | | ISO179/1eU | NoBreak |
| Impact strength of cantilever beam gap | | ASTMD256 | 600 J/m |
| Impact strength of cantilever beam gap | | ISO180/1A | 11 kJ/m² |
| Impact strength of cantilever beam gap | | ISO180/1A | 53 kJ/m² |
| Impact strength of cantilever beam gap | | ASTMD4812 | NoBreak |
| | ISO180/1U | NoBreak |
| | ISO180/1U | NoBreak |
| Dart impact equipped with measuring instruments | | ASTMD3763 | 120 J |
| Falling hammer impact | | ASTMD3029 | 149 J |
| Tensile impact strength | | ASTMD1822 | 577 kJ/m² |
| Charpy Notched Impact Strength | | ISO179/1eA | 13 kJ/m² |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTMD638 | 2100 MPa |
| Tensile modulus | | ISO527-2/1 | 2150 MPa |
| tensile strength | Yield | ASTMD638 | 65.0 MPa |
| Tensile stress | Yield | ISO527-2/50 | 65.0 MPa |
| tensile strength | Break | ASTMD638 | 70.0 MPa |
| Tensile stress | Break | ISO527-2/50 | 60.0 MPa |
| elongation | Yield | ASTMD638 | 7.0 % |
| Tensile strain | Yield | ISO527-2/50 | 7.0 % |
| elongation | Break | ASTMD638 | >110 % |
| Tensile strain | Break | ISO527-2/50 | 85 % |
| Flexural modulus | | ASTMD790 | 2200 MPa |
| Flexural modulus | | ISO178 | 2120 MPa |
| bending strength | | ISO178 | 66.0 MPa |
| bending strength | | ASTMD790 | 95.0 MPa |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Dissipation Factor | | ASTMD150 | 1.2E-03 |
| Dissipation Factor | | ASTMD150 | 0.024 |
| Volume resistivity | | ASTMD257 | >2.6E+17 ohms·cm |
| dielectric strength | | ASTMD149 | 20 kV/mm |
| dielectric constant | | ASTMD150 | 3.15 |
| dielectric constant | | ASTMD150 | 3.15 |
| dielectric constant | | ASTMD150 | 3.00 |
| Dissipation Factor | | ASTMD150 | 1.2E-03 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| | ISO75-2/Af | 125 °C |
| vicat | | ASTMD152511 | 160 °C |
| vicat | | ISO306/B50 | 154 °C |
| vicat | | ISO306/B120 | 155 °C |
| | ASTME831 | 6E-05 cm/cm/°C |
| | ISO11359-2 | 6E-05 cm/cm/°C |
| | ASTME831 | 8E-05 cm/cm/°C |
| | ISO11359-2 | 6E-05 cm/cm/°C |
| specific heat | | ASTMC351 | 1250 J/kg/°C |
| thermal conductivity | | ASTMC177 | 0.21 W/m/K |
| | ASTMD648 | 142 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare