Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Specific volume | | ASTM D792 | 0.700 cm³/g |
| Water absorption rate | | ISO 62 | 0.15 % |
| Water absorption rate | | ASTM D570 | 0.090 % |
| Water absorption rate | | ISO 62 | 0.50 % |
| Shrinkage rate | | 内部方法 | 0.40-0.50 % |
| Shrinkage rate | | 内部方法 | 0.40-0.70 % |
| Shrinkage rate | | 内部方法 | 0.70-0.90 % |
| melt mass-flow rate | | ASTM D1238 | 24 g/10min |
| Melt volume flow rate | | ISO 1133 | 12.0 cm3/10min |
| Melt volume flow rate | | ISO 1133 | 19.0 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.30-0.40 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 109 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Dart impact | | ASTM D3763 | 5.00 J |
| Dart impact | | ASTM D3763 | 17.0 J |
| Impact strength of cantilever beam gap | | ISO 180/1A | 10 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179/1eA | 9.0 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | 6.0 kJ/m² |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| bending strength | | ASTM D790 | 138 Mpa |
| bending strength | | ASTM D790 | 150 Mpa |
| Flexural modulus | | ISO 178 | 7750 Mpa |
| bending strength | | ISO 178 | 154 Mpa |
| Flexural modulus | | ASTM D790 | 5380 Mpa |
| Tensile modulus | | ASTM D638 | 9750 Mpa |
| Tensile modulus | | ISO 527-2/1 | 8500 Mpa |
| tensile strength | | ASTM D638 | 97.0 Mpa |
| tensile strength | | ISO 527-2/5 | 105 Mpa |
| tensile strength | | ASTM D638 | 91.0 Mpa |
| tensile strength | | ISO 527-2/5 | 3.00 Mpa |
| Tensile strain | | ASTM D638 | 3.0 % |
| Tensile strain | | ISO 527-2/5 | 3.0 % |
| Tensile strain | | ASTM D638 | 4.0 % |
| Tensile strain | | ISO 527-2/5 | 110 % |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 2 |
| High arc combustion index (HAI) | | UL 746 | PLC 3 |
| High arc combustion index (HAI) | | UL 746 | PLC 3 |
| High Voltage Arc Traceability Rate (HVTR) | | UL 746 | PLC 1 |
| arc resistance | | ASTM D495 | PLC 5 |
| dielectric strength | | ASTM D149 | 20 KV/mm |
| dielectric constant | | ASTM D150 | 4.00 |
| dielectric constant | | ASTM D150 | 4.00 |
| Dissipation Factor | | ASTM D150 | 3E-03 |
| Dissipation Factor | | ASTM D150 | 0.020 |
| dielectric strength | | ASTM D149 | 27 KV/mm |
| Hot wire ignition (HWI) | | UL 746 | PLC 1 |
| Volume resistivity | | ASTM D257 | 4.8E+15 ohms·cm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ISO 75-2/Af | 155 °C |
| vicat | | ASTM D152512 | 153 °C |
| vicat | | ISO 306/B50 | 148 °C |
| Heat distortion temperature | | ASTM D648 | 163 °C |
| Heat distortion temperature | | ASTM D648 | 149 °C |
| Heat distortion temperature | | ASTM D648 | 204 °C |
| RTI Str | | UL 746 | 140 °C |
| vicat | | ISO 306/B120 | 150 °C |
| Linear coefficient of thermal expansion | | ASTME831 | 2.7E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTME831 | 2E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 2.7E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTME831 | 1.1E-04 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 1.1E-04 cm/cm/°C |
| RTI Elec | | UL 746 | 140 °C |
| RTI Imp | | UL 746 | 130 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices