Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Water absorption rate | | ASTMD570 | 0.16 % |
| Water absorption rate | | ISO62 | 0.16 % |
| Water absorption rate | | ISO62 | 0.35 % |
| density | | ASTMD792 | 1.20 g/cm³ |
| Specific volume | | ASTMD792 | 0.830 cm³/g |
| density | | ASTMD792 | 1.19 g/cm³ |
| density | | ISO1183 | 1.20 g/cm³ |
| melt mass-flow rate | | ASTMD1238 | 3.0 g/10min |
| Melt volume flow rate | | ISO1133 | 3.00 cm³/10min |
| Shrinkage rate | | 内部方法 | 0.70to0.80 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTMD785 | 85 |
| Rockwell hardness | R-Scale | ASTMD785 | 122 |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| refractive index | | ASTMD542 | 1.600 |
| transmissivity | | ASTMD1003 | 85.0 % |
| Haze ratio | | ASTMD1003 | 1.0 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL94 | V-2 |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTMD638 | 2090 MPa |
| Tensile modulus | | ISO527-2/1 | 2260 MPa |
| tensile strength | Yield | ASTMD638 | 65.5 MPa |
| Tensile stress | Yield | ISO527-2/5 | 65.0 MPa |
| Tensile stress | Yield | ISO527-2/50 | 65.0 MPa |
| tensile strength | Break | ASTMD638 | 71.7 MPa |
| elongation | Yield | ASTMD638 | 7.0 % |
| Flexural modulus | | ASTMD790 | 2030 MPa |
| Flexural modulus | | ISO178 | 2120 MPa |
| bending strength | | ISO178 | 66.0 MPa |
| bending strength | | ASTMD790 | 95.1 MPa |
| Tensile strain | Yield | ISO527-2/50 | 7.0 % |
| elongation | Break | ASTMD638 | 120 % |
| Tensile strain | Break | ISO527-2/50 | >50 % |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Dart impact equipped with measuring instruments | | ASTMD3763 | 73.0 J |
| Falling hammer impact | | ASTMD3029 | 149 J |
| Tensile impact strength | | ASTMD1822 | 578 kJ/m² |
| Charpy Notched Impact Strength | | ISO179/1eA | 15 kJ/m² |
| Impact strength of cantilever beam gap | | ASTMD256 | 140 J/m |
| Impact strength of cantilever beam gap | | ASTMD256 | 640 J/m |
| Impact strength of cantilever beam gap | | ISO180/1A | 11 kJ/m² |
| Impact strength of cantilever beam gap | | ISO180/1A | 13 kJ/m² |
| Impact strength of cantilever beam gap | | ASTMD4812 | 3200 J/m |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Dissipation Factor | | ASTMD150 | 1.2E-03 |
| Dissipation Factor | | ASTMD150 | 0.024 |
| Compared to the Leakage Tracking Index (CTI) | | UL746 | PLC 3 |
| High arc combustion index (HAI) | | UL746 | PLC 4 |
| Volume resistivity | | ASTMD257 | >2.6E+17 ohms·cm |
| dielectric strength | | ASTMD149 | 20 kV/mm |
| dielectric constant | | ASTMD150 | 3.15 |
| dielectric constant | | ASTMD150 | 3.15 |
| dielectric constant | | ASTMD150 | 3.00 |
| Dissipation Factor | | ASTMD150 | 1.2E-03 |
| High Voltage Arc Traceability Rate (HVTR) | | UL746 | PLC 3 |
| Hot wire ignition (HWI) | | UL746 | PLC 2 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| vicat | | ISO306/B50 | 154 °C |
| vicat | | ISO306/B120 | 155 °C |
| RTI Elec | | UL746 | 125 °C |
| RTI Imp | | UL746 | 125 °C |
| RTI Str | | UL746 | 125 °C |
| | ASTMD648 | 143 °C |
| | ISO75-2/Af | 132 °C |
| vicat | | ASTMD152511 | 160 °C |
| | ASTME831 | 6E-05 cm/cm/°C |
| | ASTME831 | 9.2E-05 cm/cm/°C |
| | ISO11359-2 | 6E-05 cm/cm/°C |
| | ASTME831 | 6E-05 cm/cm/°C |
| | ISO11359-2 | 6E-05 cm/cm/°C |
| specific heat | | ASTMC351 | 1260 J/kg/°C |
| thermal conductivity | | ASTMC177 | 0.21 W/m/K |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare