PC/PBT XENOY™ X2500UV-YW8E099
88
- Properties:High impactNo fill
- Usages:Automotive componentsElectronic and electrical components
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|---|---|---|
| melt mass-flow rate | ASTM D1238 | 9.0 g/10min | |
| Melt volume flow rate | ISO 1133 | 4.00 cm3/10min | |
| Shrinkage rate | 内部方法 | 0.50-0.80 % | |
| 内部方法 | 0.50-0.80 % | ||
| 内部方法 | 0.50-0.80 % | ||
| Water absorption rate | ISO 62 | 0.70 % | |
| ISO 62 | 0.20 % | ||
| Shrinkage rate | 内部方法 | 0.50-0.80 % | |
| 内部方法 | 0.50-0.80 % |
| hardness | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ball-indentation hardness | ISO 2039-1 | 95.0 Mpa |
| flammability | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Burning wire flammability index | IEC 60695-2-12 | 750 °C | |
| UL flame retardant rating | UL 94 | HB |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|---|---|---|
| tensile strength | ASTM D638 | 55.0 Mpa | |
| ISO 527-2/50 | 56.0 Mpa | ||
| elongation | ASTMD638 | 5.0 % | |
| ASTM D638 | 5.0 % | ||
| ASTM D638 | 100 % | ||
| ASTM D638 | 80 % | ||
| ISO 527-2/50 | 70 % | ||
| Flexural modulus | ASTM D790 | 2100 Mpa | |
| ASTM D790 | 2150 Mpa | ||
| ISO 178 | 2150 Mpa | ||
| Tensile modulus | ASTM D638 | 2200 Mpa | |
| ISO 527-2/1 | 2200 Mpa | ||
| tensile strength | ASTM D638 | 53.0 Mpa | |
| ASTM D638 | 56.0 Mpa | ||
| ISO 527-2/50 | 57.0 Mpa | ||
| bending strength | ASTM D790 | 79.0 Mpa | |
| ISO 178 | 80.0 Mpa | ||
| ASTM D790 | 79.0 Mpa | ||
| Taber abraser | 内部方法 | 20.0 mg | |
| Tensile modulus | ASTM D638 | 2200 Mpa | |
| tensile strength | ASTM D638 | 56.0 Mpa | |
| ASTM D638 | 55.0 Mpa | ||
| elongation | ASTM D638 | 5.0 % | |
| ASTM D638 | 80 % | ||
| Flexural modulus | ASTM D790 | 2150 Mpa | |
| ISO 178 | 2150 Mpa | ||
| bending strength | ISO 178 | 80.0 Mpa | |
| ASTM D790 | 79.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | 30 kJ/m² | |
| ISO 179/1eA | 50 kJ/m² | ||
| Impact strength of simply supported beam without notch | ISO 179/1eU | 无断裂 | |
| Suspended wall beam without notch impact strength | ISO 180/1U | 无断裂 | |
| Dart impact | ASTM D3763 | 60.0 J | |
| Charpy Notched Impact Strength | ISO 179/1eA | 30 kJ/m² | |
| ISO 179/1eA | 50 kJ/m² | ||
| Impact strength of simply supported beam without notch | ISO 179/1eU | 无断裂 | |
| Suspended wall beam without notch impact strength | ISO 180/1U | 无断裂 |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Surface Resistivity | IEC 60093 | >1.0E+15 ohms | |
| Volume resistivity | IEC 60093 | >1.0E+14 ohms·cm | |
| dielectric strength | IEC 60243-1 | 17 KV/mm | |
| relative permittivity | IEC 60250 | 3.30 | |
| IEC 60250 | 3.30 | ||
| IEC 60250 | 3.10 | ||
| Dissipation Factor | IEC 60250 | 2E-03 | |
| IEC 60250 | 2E-03 | ||
| IEC 60250 | 0.020 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Heat distortion temperature | ISO 75-2/Bf | 126 °C | |
| ASTM D648 | 108 °C | ||
| ISO 75-2/Af | 108 °C | ||
| vicat | ASTMD152512 | 135 °C | |
| ISO 306/A50 | 145 °C | ||
| ISO 306/B120 | 136 °C | ||
| ball-indentation hardness | IEC 60695-10-2 | 通过 | |
| Linear coefficient of thermal expansion | ASTME831 | 8E-05 cm/cm/°C | |
| ISO 11359-2 | 8.2E-05 cm/cm/°C | ||
| ASTME831 | 8.5E-05 cm/cm/°C | ||
| ISO 11359-2 | 8.7E-05 cm/cm/°C | ||
| thermal conductivity | ISO 8302 | 0.18 W/m/K | |
| Heat distortion temperature | ISO 75-2/Af | 108 °C | |
| vicat | ASTMD152511 | 135 °C | |
| Heat distortion temperature | ISO 75-2/Bf | 126 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Contact Us
Get App
Top