Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTM D1238 | 8.0 g/10 min |
| Melt volume flow rate | | ISO 1133 | 5.00 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.50 - 0.80 % |
| Water absorption rate | | ISO 62 | 0.32 % |
| Water absorption rate | | ISO 62 | 0.12 % |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| transmissivity | | ASTM D1003 | > 85.0 % |
| Haze ratio | | ASTM D1003 | 1.6 % |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 2300 Mpa |
| Tensile modulus | | ISO 527-2/1 | 2660 Mpa |
| tensile strength | | ASTM D638 | 61.0 Mpa |
| tensile strength | | ISO 527-2/50 | 62.0 Mpa |
| tensile strength | | ASTM D638 | 65.0 Mpa |
| tensile strength | | ISO 527-2/50 | 59.0 Mpa |
| elongation | | ASTM D638 | 6.0 % |
| elongation | | ISO 527-2/50 | 5.4 % |
| elongation | | ASTM D638 | 130 % |
| elongation | | ISO 527-2/50 | 110 % |
| Flexural modulus | | ASTM D790 | 2320 Mpa |
| Flexural modulus | | ISO 178 | 2180 Mpa |
| bending strength | | ISO 178 | 92.0 Mpa |
| bending strength | | ASTM D790 | 96.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Dart impact | | ASTM D3763 | 79.0 J |
| injection | Test Condition | Test Method | Test Result |
|---|
| drying temperature | | | 80 to 95 °C |
| drying time | | | 3.0 to 5.0 hr |
| Suggested maximum moisture content | | | 0.020 % |
| Suggested injection volume | | | 40 to 80 % |
| Temperature at the rear of the barrel | | | 240 to 250 °C |
| Temperature in the middle of the barrel | | | 245 to 265 °C |
| Temperature at the front of the material cylinder | | | 250 to 270 °C |
| Spray nozzle temperature | | | 250 to 270 °C |
| Processing (melt) temperature | | | 250 to 270 °C |
| Temperature | | | 45 to 60 °C |
| Back pressure | | | 0.200 to 0.500 Mpa |
| screw speed | | | 20 to 100 rpm |
| Exhaust hole depth | | | 0.013 to 0.020 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 104 °C |
| Heat distortion temperature | | ISO 75-2/Af | 105 °C |
| vicat | | ASTM D15259 | 125 °C |
| vicat | | ISO 306/B120 | 127 °C |
| Linear coefficient of thermal expansion | | ASTM E831 | 6.0E-5 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTM E831 | 7.0E-5 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 6.3E-5 cm/cm/°C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices