ABS Generic ABS+PC - Glass Fiber Generic

0
  • Properties:
    Fillers
    glass fiber reinforced materials

Technical Data Sheet

physical property Test ConditionTest MethodTest Result
Shrinkage rateISO 294-40.20to0.46 %
Water absorption rateASTM D5700.098to0.10 %
Water absorption rateISO 620.29to0.60 %
Water absorption rateISO 620.20to0.25 %
densityASTM D7921.17to1.43 g/cm³
densityISO 11831.17to1.43 g/cm³
melt mass-flow rateASTM D12382.3to4.1 g/10min
melt mass-flow rateISO 11339.7to30 g/10min
Melt volume flow rateISO 113314.8to20.0 cm³/10min
Shrinkage rateASTM D9550.15to0.43 %
Shrinkage rateASTM D9550.25to0.65 %
hardnessTest ConditionTest MethodTest Result
Rockwell hardnessASTM D785111to120
flammabilityTest ConditionTest MethodTest Result
Hot filament ignition temperatureIEC 60695-2-13642to755 °C
Mechanical propertiesTest ConditionTest MethodTest Result
Tensile modulusASTM D6383450to9650 MPa
Tensile modulusISO 527-23300to7800 MPa
bending strengthASTM D79094.3to173 MPa
bending strengthISO 17892.3to144 MPa
bending strengthASTM D790101to138 MPa
bending strengthASTM D79099.7to142 MPa
tensile strength ASTM D63858.3to125 MPa
tensile strength ISO 527-258.3to95.6 MPa
tensile strength ASTM D63848.8to110 MPa
tensile strength ISO 527-250.9to95.1 MPa
tensile strength ASTM D63873.1to125 MPa
elongationASTM D6382.5to5.0 %
elongationISO 527-22.1to5.5 %
elongationASTM D6381.5to7.4 %
elongationISO 527-22.0to5.1 %
Flexural modulusASTM D7902450to8580 MPa
Flexural modulusISO 1783000to8230 MPa
Impact resistanceTest ConditionTest MethodTest Result
Charpy Notched Impact StrengthISO 1796.9to10 kJ/m²
Impact strength of simply supported beam without notchISO 17925to40 kJ/m²
Impact strength of cantilever beam gapASTM D25658to130 J/m
Impact strength of cantilever beam gapISO 1804.0to14 kJ/m²
Suspended wall beam without notch impact strengthASTM D256310to800 J/m
Suspended wall beam without notch impact strengthISO 18021to38 kJ/m²
Dart impactASTM D376313.3to35.0 J
Electrical performanceTest ConditionTest MethodTest Result
Surface ResistivityASTM D2571.0E+2到2.5E+14 ohms
Surface ResistivityIEC 600939.8E+14到1.0E+15 ohms
Volume resistivityASTM D2575.1E+5到1.3E+16 ohms·cm
Volume resistivityIEC 600931.0E+13到1.0E+15 ohms·cm
dielectric strengthASTM D14926to36 kV/mm
arc resistanceASTM D49569.0to106 sec
Compared to the Leakage Tracking Index (CTI)IEC 60112PLC 2
High arc combustion index (HAI)UL 746PLC 0
High Voltage Arc Traceability Rate (HVTR)UL 746PLC 4 mm/min
Hot wire ignition (HWI)UL 746PLC 0 sec
Thermal performanceTest ConditionTest MethodTest Result
Linear coefficient of thermal expansionASTME8313.2E-5到7.3E-5 cm/cm/°C
Linear coefficient of thermal expansionISO 11359-27.9E-5到8.3E-5 cm/cm/°C
Heat distortion temperatureASTM D64892.0to139 °C
Heat distortion temperatureISO 75-2/B89.0to140 °C
Heat distortion temperatureASTM D64887.5to136 °C
Heat distortion temperatureISO 75-2/A112to124 °C
vicatASTM D1525101to144 °C
vicatISO 30699.4to140 °C
Linear coefficient of thermal expansionASTM D6966.5E-5到8.2E-5 cm/cm/°C
Linear coefficient of thermal expansionASTM D6962.9E-5到6.1E-5 cm/cm/°C
Linear coefficient of thermal expansionASTME8312.9E-5到7.7E-5 cm/cm/°C
Linear coefficient of thermal expansionISO 11359-21.7E-5到7.7E-5 cm/cm/°C
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Contact Us

Get App

Top