Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Specific volume | | ASTM D792 | 0.660 cm³/g |
| Shrinkage rate | | 内部方法 | 0.30 - 0.50 % |
| Shrinkage rate | | 内部方法 | 0.50 - 0.80 % |
| Shrinkage rate | | 内部方法 | 0.40 - 0.60 % |
| Shrinkage rate | | 内部方法 | 0.60 - 0.90 % |
| Water absorption rate | | ASTM D570 | 0.060 % |
| Outdoor applicability | | UL 746C | f2 |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 119 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| tensile strength | | ASTM D638 | 110 Mpa |
| Flexural modulus | | ASTM D790 | 6890 Mpa |
| bending strength | | ASTM D790 | 189 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Suspended wall beam without notch impact strength | | ASTM D4812 | 640 J/m |
| Dart impact | | ASTM D3763 | 6.00 J |
| Dart impact | | ASTM D3763 | 8.00 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Volume resistivity | | ASTM D257 | 5.9E+16 ohms·cm |
| dielectric strength | | ASTM D149 | 29 KV/mm |
| dielectric strength | | ASTM D149 | 24 KV/mm |
| dielectric constant | | ASTM D150 | 3.60 |
| dielectric constant | | ASTM D150 | 3.60 |
| Dissipation Factor | | ASTM D150 | 1.4E-3 |
| Dissipation Factor | | ASTM D150 | 0.020 |
| arc resistance | | ASTM D495 | PLC 6 |
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 4 |
| High arc combustion index (HAI) | | UL 746 | PLC 3 |
| High Voltage Arc Traceability Rate (HVTR) | | UL 746 | PLC 2 |
| Hot wire ignition (HWI) | | UL 746 | PLC 1 |
| injection | Test Condition | Test Method | Test Result |
|---|
| drying temperature | | | 120 °C |
| drying time | | | 3.0 to 4.0 hr |
| Suggested maximum moisture content | | | 0.020 % |
| Suggested injection volume | | | 40 to 80 % |
| Temperature at the rear of the barrel | | | 240 to 255 °C |
| Temperature in the middle of the barrel | | | 245 to 260 °C |
| Temperature at the front of the material cylinder | | | 250 to 265 °C |
| Spray nozzle temperature | | | 245 to 260 °C |
| Processing (melt) temperature | | | 250 to 265 °C |
| Temperature | | | 65 to 90 °C |
| Back pressure | | | 0.300 to 0.700 Mpa |
| screw speed | | | 50 to 80 rpm |
| Exhaust hole depth | | | 0.025 to 0.038 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 215 °C |
| Heat distortion temperature | | ASTM D648 | 176 °C |
| Linear coefficient of thermal expansion | | ASTM E831 | 2.3E-5 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTM E831 | 1.6E-5 cm/cm/°C |
| RTI Elec | | UL 746 | 125 °C |
| RTI Imp | | UL 746 | 110 °C |
| RTI | | UL 746 | 125 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices