Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Specific volume | | ASTM D792 | 0.610 cm³/g |
| melt mass-flow rate | | ASTM D1238 | 42 g/10 min |
| Molten Volume Flow Rate (MVR) | | ISO 1133 | 29.0 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.10 到 0.50 % |
| Shrinkage rate | | 内部方法 | 0.50 到 0.70 % |
| Shrinkage rate | | 内部方法 | 0.40 到 0.80 % |
| Shrinkage rate | | 内部方法 | 0.50 到 1.0 % |
| Water absorption rate | | ISO 62 | 0.090 % |
| Water absorption rate | | ISO 62 | 0.070 % |
| Outdoor applicability | | UL 746C | f2 |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 119 |
| Rockwell hardness | | ISO 2039-2 | 119 |
| | ISO 2039-1 | 118 Mpa |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-2 |
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | 5VA |
| Burning wire flammability index | | IEC 60695-2-12 | 960 °C |
| Limiting Oxygen Index | | ISO 4589-2 | 32 % |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 12000 Mpa |
| Tensile modulus | | ISO 527-2/1 | 10000 Mpa |
| tensile strength | | ASTM D638 | 120 Mpa |
| tensile strength | | ISO 527-2/5 | 120 Mpa |
| tensile strength | | ASTM D638 | 120 Mpa |
| tensile strength | | ISO 527-2/5 | 120 Mpa |
| elongation | | ASTM D638 | 2.0 % |
| elongation | | ISO 527-2/5 | 1.9 % |
| elongation | | ASTM D638 | 2.0 % |
| elongation | | ISO 527-2/5 | 1.9 % |
| Flexural modulus | | ASTM D790 | 9800 Mpa |
| Flexural modulus | | ISO 178 | 9500 Mpa |
| Bending stress | | ISO 178 | 180 Mpa |
| Bending stress | | ASTM D790 | 186 Mpa |
| | 内部方法 | 22.0 mg |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam gap 7 | | ISO 179/1eA | 6.0 kJ/m² |
| Impact strength of simply supported beam gap 7 | | ISO 179/1eA | 7.0 kJ/m² |
| The impact strength of a simply supported beam without a notch is 7 | | ISO 179/1eU | 50 kJ/m² |
| The impact strength of a simply supported beam without a notch is 7 | | ISO 179/1eU | 50 kJ/m² |
| | ASTM D4812 | 620 J/m |
| | ISO 180/1U | 45 kJ/m² |
| | ISO 180/1U | 45 kJ/m² |
| Dart impact equipped with measuring instruments | | ASTM D3763 | 5.00 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | IEC 60093 | > 1.0E+15 ohms |
| Volume resistivity | | ASTM D257, IEC 60093 | > 1.0E+15 ohms·cm |
| dielectric strength | | ASTM D149 | 24 KV/mm |
| dielectric strength | | ASTM D149 | 19 KV/mm |
| dielectric strength | | IEC 60243-1 | 23 KV/mm |
| dielectric strength | | IEC 60243-1 | 22 KV/mm |
| dielectric strength | | IEC 60243-1 | 16 KV/mm |
| dielectric constant | | ASTM D150, IEC 60250 | 3.80 |
| dielectric constant | | ASTM D150 | 3.70 |
| dielectric constant | | IEC 60250 | 3.30 |
| dielectric constant | | IEC 60250 | 3.30 |
| dielectric constant | | IEC 60250 | 3.30 |
| Dissipation Factor | | ASTM D150, IEC 60250 | 2.0E-3 |
| Dissipation Factor | | ASTM D150 | 0.020 |
| Dissipation Factor | | IEC 60250 | 1.0E-3 |
| Dissipation Factor | | IEC 60250 | 1.0E-3 |
| Dissipation Factor | | IEC 60250 | 0.010 |
| Arc resistance 11 | | ASTM D495 | PLC 6 |
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 3 |
| CTI | | IEC 60112 | 175 V |
| CTI | | IEC 60112 | 125 V |
| High arc combustion index (HAI) | | UL 746 | PLC 0 |
| High Voltage Arc Traceability Rate (HVTR) | | UL 746 | PLC 4 |
| Hot wire ignition (HWI) | | UL 746 | PLC 2 |
| injection | Test Condition | Test Method | Test Result |
|---|
| drying temperature | | | 120 °C |
| drying time | | | 3.0 到 4.0 hr |
| Suggested maximum moisture content | | | 0.020 % |
| Suggested injection volume | | | 40 到 80 % |
| Temperature at the rear of the barrel | | | 245 到 265 °C |
| Temperature in the middle of the barrel | | | 250 到 270 °C |
| Temperature at the front of the material cylinder | | | 255 到 275 °C |
| Spray nozzle temperature | | | 250 到 270 °C |
| Processing (melt) temperature | | | 255 到 275 °C |
| Temperature | | | 65 到 90 °C |
| Back pressure | | | 0.300 到 0.700 Mpa |
| screw speed | | | 50 到 80 rpm |
| Exhaust hole depth | | | 0.025 到 0.038 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Thermal deformation temperature under load | | ASTM D648 | 212 °C |
| Thermal deformation temperature under load | | ISO 75-2/Be | 220 °C |
| Thermal deformation temperature under load | | ASTM D648 | 200 °C |
| Thermal deformation temperature under load | | ISO 75-2/Ae | 195 °C |
| Thermal deformation temperature under load | | ISO 75-2/Af | 200 °C |
| vicat | | ASTM D152510, ISO 306/B50, ISO 306/B120 | 200 °C |
| vicat | | ISO 306/A50 | 220 °C |
| Ball Pressure Test | | IEC 60695-10-2 | 通过 |
| | ASTM E831, ISO 11359-2 | 2.5E-5 cm/cm/°C |
| | ISO 11359-2 | 2.5E-5 cm/cm/°C |
| | ASTM E831 | 8.9E-5 cm/cm/°C |
| | ISO 11359-2 | 8.9E-5 cm/cm/°C |
| | ISO 11359-2 | 1.2E-4 cm/cm/°C |
| thermal conductivity | | ISO 8302 | 0.25 W/m/K |
| RTI Elec | | UL 746 | 130 °C |
| RTI Imp | | UL 746 | 130 °C |
| RTI | | UL 746 | 140 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices