Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Water absorption rate | | ISO 62 | 0.22 % |
| density | | ASTM D792 | 1.04 g/cm³ |
| density | | ISO 1183 | 1.04 g/cm³ |
| melt mass-flow rate | | ASTM D1238 | 1.5 g/10min |
| melt mass-flow rate | | ASTM D1238 | 19 g/10min |
| Melt volume flow rate | | ASTM D1238 | 4.80 cm3/10min |
| Melt volume flow rate | | ISO 1133 | 19.0 cm3/10min |
| Shrinkage rate | | ASTM D955 | 0.40-0.70 % |
| Shrinkage rate | | ISO 294-4 | 0.40-0.70 % |
| Water absorption rate | | ASTM D570 | 1.0 % |
| Water absorption rate | | ISO 62 | 1.0 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 103 |
| ball-indentation hardness | | ISO 2039-1 | 97.0 Mpa |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| Yellowness Index | | DIN 6167 | 13 YI |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 2300 Mpa |
| Tensile modulus | | ISO 527-2 | 2300 Mpa |
| tensile strength | | ASTM D638 | 45.0 Mpa |
| tensile strength | | ISO 527-2 | 45.0 Mpa |
| Tensile strain | | ISO 527-2 | 2.6 % |
| elongation | | ASTM D638 | 2.6 % |
| Nominal tensile fracture strain | | ISO 527-2 | 10 % |
| Flexural modulus | | ASTM D790 | 2300 Mpa |
| bending strength | | ASTM D790 | 65.0 Mpa |
| bending strength | | ISO 178 | 65.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ISO 179 | 8.0 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179 | 22 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO 179 | 100 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO 179 | 180 kJ/m² |
| Impact strength of cantilever beam gap | | ASTM D256 | 59 J/m |
| Impact strength of cantilever beam gap | | ASTM D256 | 100 J/m |
| Impact strength of cantilever beam gap | | ASTM D256 | 300 J/m |
| Impact strength of cantilever beam gap | | ISO 180/A | 8.0 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/A | 26 kJ/m² |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | IEC 60093 | 1E+13 ohms |
| Volume resistivity | | ASTM D257 | >1.0E+15 ohms·cm |
| Volume resistivity | | IEC 60093 | 1E+15 ohms·cm |
| dielectric constant | | ASTM D150 | 2.80 |
| relative permittivity | | IEC 60250 | 2.90 |
| relative permittivity | | IEC 60250 | 2.80 |
| Dissipation Factor | | IEC 60250 | 4.8E-03 |
| Dissipation Factor | | IEC 60250 | 7.9E-03 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Linear coefficient of thermal expansion | | ISO 11359-2 | 8.0E-5to1.1E-4 cm/cm/°C |
| thermal conductivity | | DIN 52612 | 0.17 W/m/K |
| Heat distortion temperature | | ASTM D648 | 90.6 °C |
| Heat distortion temperature | | ASTM D648 | 104 °C |
| Heat distortion temperature | | ISO 75-2/B | 99.0 °C |
| Heat distortion temperature | | ASTM D648 | 77.8 °C |
| Heat distortion temperature | | ASTM D648 | 98.9 °C |
| Heat distortion temperature | | ISO 75-2/A | 94.0 °C |
| vicat | | ISO 306/A50 | 105 °C |
| vicat | | ISO 306/B50 | 96.0 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare