Technical Data Sheet
Compare
| physical property | Test Condition | Test Method | Test Result |
|---|
| Shrinkage rate | | ISO 294-4 | 0.2-0.6 % |
| Shrinkage rate | | ISO 294-4 | 0.40-0.60 % |
| Shrinkage rate | | ISO 294-4 | 0.20-0.60 % |
| Water absorption rate | | ISO 62 | 0.020 % |
| density | | ASTMD792 | 1.65 g/cm³ |
| Specific volume | | ASTM D792 | 0.611 cm³/g |
| Shrinkage rate | | ASTM D955 | 0.20-0.30 % |
| Shrinkage rate | | ASTM D955 | 0.50-0.70 % |
| Biochemical properties | Test Condition | Test Method | Test Result |
|---|
| Filling amount | | | 40 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 100 |
| Rockwell hardness | | ISO 2039-2 | 100 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | 5VA |
| Limiting Oxygen Index | | ISO 4589-2 | 47 % |
| Basic performance | Test Condition | Test Method | Test Result |
|---|
| density | | ISO 1183 | 1.65 g/cm³ |
| Water absorption rate | | ASTM-D570 | 0.02 % |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| Shrinkage rate | | 内部方法 | 3.18 mm |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| tensile strength | | ISO 527 | 195 Mpa |
| Tensile modulus | | ISO 527 | 14700 Mpa |
| bending strength | | ISO 178 | 285 Mpa |
| Flexural modulus | | ISO 178 | 14500 Mpa |
| Impact strength of cantilever beam gap | | ISO 180/1A | 10 kJ/m² |
| Rockwell hardness | | ASTM-D785 | 100 R-Scale |
| tensile strength | | ASTM D638 | 200 Mpa |
| tensile strength | | ISO 527-2/1A/5 | 195 Mpa |
| elongation | | ASTM D638 | 1.7 % |
| elongation | | ISO 527-2/1A/5 | 1.9 % |
| Flexural modulus | | ISO 178 | 14500 Mpa |
| bending strength | | ISO 178 | 285 Mpa |
| Tensile modulus | | ASTM D638 | 14500 Mpa |
| Tensile modulus | | ASTM D638 | 11900 Mpa |
| Tensile modulus | | ASTM D638 | 4270 Mpa |
| Tensile modulus | | ASTM D638 | 3240 Mpa |
| Tensile modulus | | ISO 527-2/1A/1 | 14700 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ISO 179/1eA | 10 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179/1eA | 10 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 53 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 53 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | 10 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | 10 kJ/m² |
| Suspended wall beam without notch impact strength | | ISO 180/1U | 34 kJ/m² |
| Filling analysis | Test Condition | Test Method | Test Result |
|---|
| SpecificHeatCapacity of Melt | | 内部方法 | 1500 J/kg/°C |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | IEC 60093 | >1.0E+15 ohms |
| Volume resistivity | | ASTM D257 | 1E+16 ohms·cm |
| Volume resistivity | | IEC 60093 | >1.0E+15 ohms·cm |
| dielectric strength | | IEC 60243-1 | 28 KV/mm |
| dielectric constant | | ASTM D150 | 3.50 |
| dielectric constant | | ASTM D150 | 3.50 |
| dielectric constant | | IEC 60250 | 4.60 |
| Dissipation Factor | | ASTM D150 | 1E-03 |
| Dissipation Factor | | ASTM D150 | 1E-03 |
| Dissipation Factor | | IEC 60250 | 6.2E-03 |
| arc resistance | | ASTM D495 | 134 sec |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | PLC 4 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ISO 75-A | 270 °C |
| UL flame retardant rating | | UL 94 | V-0 |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 4.2E-05 cm/cm/°C |
| Heat distortion temperature | | ASTM D648 | 280 °C |
| Heat distortion temperature | | ASTM D648 | 265 °C |
| Heat distortion temperature | | ISO 75-2/A | 270 °C |
| Heat distortion temperature | | ISO 75-2/C | 215 °C |
| Glass Transition Temperature | | ISO 11357-2 | 90.0 °C |
| melting temperature | | ISO 11357-3 | 280 °C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 2.6E-05 cm/cm/°C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
