Technical Data Sheet
Compare
| physical property | Test Condition | Test Method | Test Result |
|---|
| Shrinkage rate | | TORAY | 0.70 % |
| Taber wear resistance | | ASTM D-D1044 | 50 mg/1000次 |
| coefficient of friction | | ASTM D-1894 | 0.25 |
| limiting pv value | | TORAY | 815 KJ/m |
| Shrinkage rate | | TORAY | 0.20 % |
| Shrinkage rate | | 内部方法 | 0.80 % |
| Shrinkage rate | | 内部方法 | 0.20 % |
| Water absorption rate | | ISO 62 | 0.020 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ISO 2039-2 | 122 |
| other | Test Condition | Test Method | Test Result |
|---|
| characteristic | | | 40%加纤.增强.标准 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-0 |
| Basic performance | Test Condition | Test Method | Test Result |
|---|
| Water absorption rate | | ASTM D-570 | 0.02 % |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| BarFlowLength | | 内部方法 | 135 mm |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ASTM D256/ISO 179 | 11 kg·cm/cm(J/M)ft·lb/in |
| Charpy Notched Impact Strength | | ASTM D256/ISO 179 | 55 kg·cm/cm(J/M)ft·lb/in |
| elongation at break | | ASTM D638/ISO 527 | 1.8 % |
| tensile strength | | ASTM D638/ISO 527 | 200 kg/cm²(MPa)[Lb/in²] |
| Rockwell hardness | | ASTM D785 | 122 |
| Flexural modulus | | ASTM D790/ISO 178 | 15.5 kg/cm²(MPa)[Lb/in²] |
| bending strength | | ASTM D790/ISO 178 | 305 kg/cm²(MPa)[Lb/in²] |
| elongation at break | | ASTM D-638 | 3.6 % |
| Impact strength of cantilever beam gap | | ASTM D-256 | 130 J/m |
| Impact strength of cantilever beam gap | | ASTM D-256 | 55 KJ/m |
| Flexural modulus | | ASTM D-790 | 13.3 GPa |
| tensile strength | | ASTM D-638 | 207 Mpa |
| bending strength | | ASTM D-790 | 275 Mpa |
| Rockwell hardness | | ASTM D-785 | 122 R |
| compressive strength | | ASTM D-732 | 80 |
| Taber abraser | | ISO 9352 | 50.0 mg |
| tensile strength | | ISO 527-2 | 200 Mpa |
| Tensile strain | | ISO 527-2 | 1.8 % |
| Flexural modulus | | ISO 178 | 15500 Mpa |
| bending strength | | ISO 178 | 305 Mpa |
| shear strength | | JISK7214 | 80.0 Mpa |
| coefficient of friction | | | 0.25 |
| Other performance | Test Condition | Test Method | Test Result |
|---|
| | TORAY | 100 |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam without notch | | ISO 179 | 55 kJ/m² |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| dielectric constant | | ASTM D150/IEC 60250 | 4.2 |
| Volume resistivity | | ASTM D257/IEC 60093 | 1014 Ω.cm |
| dielectric constant | | ASTM D-150 | 3.8 |
| Volume resistivity | | ASTM D-257 | 10 Ω.m |
| arc resistance | | ASTM D-495 | 127 |
| Dissipation Factor | | ASTM D-150 | 0.002 |
| dielectric strength | | ASTM D-149 | 21 MV/m |
| Volume resistivity | | IEC 60093 | 1E+16 ohms·cm |
| dielectric strength | | IEC 60243-1 | 24 KV/mm |
| dielectric constant | | IEC 60250 | 4.20 |
| Dissipation Factor | | IEC 60250 | 2E-03 |
| Physical properties | Test Condition | Test Method | Test Result |
|---|
| density | | ASTM D792/ISO 1183 | 1.66 |
| Shrinkage rate | | ASTM D955 | 0.36 % |
| Water absorption rate | | ASTM D570/ISO 62 | 0.02 % |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Combustibility (rate) | | UL 94 | V-0 |
| Heat distortion temperature | | ASTM D648/ISO 75 | >260 ℃（℉） |
| melting temperature | | | 278 ℃（℉） |
| Heat distortion temperature | | ASTM D-648 | >260 °C |
| Linear coefficient of thermal expansion | | ASTM D-696 | 2.3 |
| Linear coefficient of thermal expansion | | ASTM D-696 | 3.2 |
| melting temperature | | DSC | 278 °C |
| Heat distortion temperature | | ISO 75-2/A | 260 °C |
| melting temperature | | ISO 11357-3 | 278 °C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 2.3E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 3.1E-05 cm/cm/°C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
