Impact strength of simply supported beam without notch
23°C
ISO 179/1eU
200 kJ/m²
Impact strength of simply supported beam without notch
-30°C
ISO 179/1eU
200 kJ/m²
Charpy Notched Impact Strength
23°C
ISO 179/1eA
8.0 kJ/m²
Charpy Notched Impact Strength
-30°C
ISO 179/1eA
7.0 kJ/m²
Impact strength of cantilever beam gap
23°C
ISO 180/1A
7.0 kJ/m²
flammability
Test Condition
Test Method
Test Result
Burning rate
1.00mm
ISO 3795
20 mm/min
UL flame retardant rating
0.8mm
UL 94
HB
UL flame retardant rating
1.5mm
UL 94
HB
UL flame retardant rating
0.8mm
IEC 60695-11-10,-20
HB
UL flame retardant rating
1.5mm
IEC 60695-11-10,-20
HB
Extreme Oxygen Index
ISO 4589-2
23 %
FMVSS flammability
FMVSS302
B
Atomization
F-value(refraction)
ISO 6452
95 %
Atomization
G-value(condensate)
ISO 6452
2E-04 g
mechanical properties
Test Condition
Test Method
Test Result
Friction coefficient
vs.Itself-Dynamic,1hr
ASTM D1894
0.25
Bending modulus
ISO 178
3000 Mpa
Tensile creep modulus
1000hr
ISO 899-1
1500 Mpa
Tensile creep modulus
1hr
ISO 899-1
2800 Mpa
Nominal tensile fracture strain
ISO 527-2
23 %
Tensile modulus
ISO 527-2
3300 Mpa
tensile strength
Yield
ISO 527-2
71.0 Mpa
Tensile strain
Yield
ISO 527-2
12 %
thermal performance
Test Condition
Test Method
Test Result
AnnealingTemperature
160 °C
Linear coefficient of thermal expansion
TD
ISO 11359-2
1.2E-04 cm/cm/°C
Linear coefficient of thermal expansion
MD
ISO 11359-2
1.2E-04 cm/cm/°C
Linear coefficient of thermal expansion
MD:23to55°C
ASTME831
1E-04 cm/cm/°C
Melting temperature
ISO 11357-3
178 °C
Vicat softening temperature
ISO 306/B50
160 °C
Hot deformation temperature
1.8MPa,Unannealed
ISO 75-2/A
94.0 °C
Hot deformation temperature
0.45MPa,Unannealed
ISO 75-2/B
162 °C
Effective thermal diffusivity coefficient
8E-08 m²/s
AnnealingTime-Optional
30.0 min/mm
Physical properties
Test Condition
Test Method
Test Result
density
ISO 1183
1.42 g/cm³
melt mass-flow rate
ISO 1133
25 g/10min
Melt Volume Flow Rate (MVR)
190°C/2.16kg
ISO 1133
21.0 cm3/10min
Shrinkage rate
TD
ISO 294-4
1.9 %
Shrinkage rate
MD
ISO 294-4
1.9 %
Water absorption rate
Saturation,23°C,2.00mm
ISO 62
1.4 %
Water absorption rate
Equilibrium,23°C,2.00mm,50%RH
ISO 62
0.40 %
Electrical performance
Test Condition
Test Method
Test Result
Volume resistivity
IEC 60093
1E+14 ohms·cm
Relative permittivity
100Hz
IEC 60250
3.80
Relative permittivity
1MHz
IEC 60250
3.80
Surface resistivity
IEC 60093
>1.0E+15 ohms
Compared to the anti leakage trace index
IEC 60112
PLC 0
Hot wire ignition
0.750mm
UL 746
PLC 4 sec
hardness
Test Condition
Test Method
Test Result
Rockwell hardness
R-Sale
ISO 2039-2
120
Rockwell hardness
M-Sale
ISO 2039-2
92
Supplementary Information
Test Condition
Test Method
Test Result
EmissionofOrganicCompounds
VDA277
4.30 µgC/g
Emission
VDA275
<8.00 mg/kg
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.