PC Makrolon® 1837 012475
21
- Properties:High mobilityHigh impact resistanceHigh hardness
- Usages:Washing machineAutomotive interior parts
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Apparent density | ISO 60 | 0.64 g/cm³ | |
| melt mass-flow rate | ISO 1133 | 12 g/10 min | |
| Shrinkage rate | ISO 2577 | 0.60 - 0.80 % | |
| Melt volume flow rate | ISO 1133 | 11.0 cm3/10min | |
| Water absorption rate | ISO 62 | 0.12 % | |
| ISO 62 | 0.40 % | ||
| Shrinkage rate | ISO 2577 | 0.60 - 0.80 % | |
| ISO 294-4 | 0.70 % | ||
| ISO 294-4 | 0.65 % | ||
| density | ISO 1183 | 1.19 g/cm³ |
| hardness | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ball-indentation hardness | ISO 2039-1 | 104 Mpa |
| flammability | Test Condition | Test Method | Test Result |
|---|---|---|---|
| burning rate | ISO 3795 | passed | |
| auto-ignition temperature | ASTM D1929 | 530 °C | |
| UL flame retardant rating | IEC 60695-11-5 | 5.0 sec | |
| IEC 60695-11-5 | 5.0 sec | ||
| Limiting Oxygen Index | ISO 4589-2 | 30 % | |
| flash temperature | ASTM D1929 | 450 °C | |
| Hot filament ignition temperature | IEC 60695-2-13 | 825 °C | |
| IEC 60695-2-13 | 850 °C | ||
| Burning wire flammability index | IEC 60695-2-12 | 900 °C | |
| Hot filament ignition temperature | IEC 60695-2-13 | 825 °C | |
| UL flame retardant rating | UL 94 | HB | |
| Burning wire flammability index | IEC 60695-2-12 | 850 °C | |
| IEC 60695-2-12 | 875 °C |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | 60 kJ/m² | |
| ISO 179/1eA | 50 kJ/m² | ||
| Multi axis Instrumented Impact Energy | ISO 6603-2 | 55.0 J | |
| ISO 6603-2 | 50.0 J | ||
| Impact strength of cantilever beam gap | ISO 180/A | 45 kJ/m² | |
| ISO 180/A | 60 kJ/m² | ||
| Impact strength of simply supported beam without notch | ISO 179/1eU | 无断裂 | |
| ISO 179/1eU | 无断裂 | ||
| ISO 179/1eU | 无断裂 | ||
| Multi axis Instrumented Peak Impact Force | ISO 6603-2 | 5800 N | |
| ISO 6603-2 | 4900 N |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|---|---|---|
| bending strength | ISO 178 | 6.8 % | |
| ISO 178 | 86.0 Mpa | ||
| ISO 178 | 68.0 Mpa | ||
| Flexural modulus | ISO 178 | 2200 Mpa | |
| Nominal tensile fracture strain | ISO 527-2/50 | > 50 % | |
| Tensile strain | ISO 527-2/50 | 5.7 % | |
| ISO 527-2/50 | 120 % | ||
| tensile strength | ISO 527-2/50 | 60.0 Mpa | |
| ISO 527-2/50 | 58.0 Mpa | ||
| Tensile modulus | ISO 527-2/1 | 2200 Mpa |
| injection | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Exhaust hole depth | 0.025 to 0.075 mm | ||
| Temperature | 70 to 110 °C | ||
| Back pressure | 10.0 to 20.0 Mpa | ||
| Processing (melt) temperature | 280 to 320 °C | ||
| Temperature at the front of the material cylinder | 285 to 305 °C | ||
| Spray nozzle temperature | 270 to 305 °C | ||
| Temperature at the rear of the barrel | 250 to 270 °C | ||
| Temperature in the middle of the barrel | 270 to 290 °C | ||
| Suggested injection volume | 30 to 70 % | ||
| Drying time - Dry Air Dryer | 4.0 hr | ||
| Suggested maximum moisture content | < 0.020 % | ||
| Drying Temperature - Dry Air Dryer | 120 °C |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| relative permittivity | IEC 60250 | 3.20 | |
| dielectric strength | IEC 60243-1 | 34 KV/mm | |
| Volume resistivity | IEC 60093 | 1.0E+16 ohms·cm | |
| Surface Resistivity | IEC 60093 | 1.0E+16 ohms | |
| Dissipation Factor | IEC 60250 | 0.013 | |
| Compared to the Leakage Tracking Index (CTI) | IEC 60112 | PLC 3 | |
| IEC 60112 | PLC 4 | ||
| Dissipation Factor | IEC 60250 | 1.4E-3 | |
| relative permittivity | IEC 60250 | 3.10 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Heat distortion temperature | ISO 75-2/B | 134 °C | |
| ISO 75-2/A | 121 °C | ||
| vicat | ISO 306/B50 | 141 °C | |
| Glass Transition Temperature | ISO 11357-2 | 143 °C | |
| thermal conductivity | ISO 8302 | 0.20 W/m/K | |
| Linear coefficient of thermal expansion | ISO 11359-2 | 7.0E-5 cm/cm/°C | |
| ball-indentation hardness | IEC 60695-10-2 | 通过 | |
| Linear coefficient of thermal expansion | ISO 11359-2 | 7.0E-5 cm/cm/°C | |
| vicat | ISO 306/B120 | 143 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Contact Us
Get App
Top