Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| density | | ISO 1183 | 1.13 g/cm³ |
| melt mass-flow rate | | ISO 1133 | 8.0 g/10 min |
| Melt volume flow rate | | ISO 1133 | 8.00 cm3/10min |
| Shrinkage rate | | ISO 294-4 | 0.90 % |
| Shrinkage rate | | ISO 294-4 | 0.90 % |
| Water absorption rate | | ISO 62 | 0.30 % |
| Water absorption rate | | ISO 62 | 0.12 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| ball-indentation hardness | | ISO 2039-1 | 130 Mpa |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| refractive index | | ISO 489 | 1.566 |
| transmissivity | | ISO 13468-2 | 89.0 % |
| electrolytic corrosion | | IEC 60426 | A1 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Burning wire flammability index | | IEC 60695-2-12 | 800 °C |
| Limiting Oxygen Index | | ISO 4589-2 | 25 % |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ISO 527-2/1 | 2450 Mpa |
| tensile strength | | ISO 527-2/50 | 76.0 Mpa |
| Tensile strain | | ISO 527-2/50 | 6.9 % |
| Nominal tensile fracture strain | | ISO 527-2/50 | > 50 % |
| Flexural modulus | | ISO 178 | 2450 Mpa |
| bending strength | | ISO 178 | 110 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 无断裂 |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 无断裂 |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Surface Resistivity | | IEC 60093 | 1.0E+16 ohms |
| Volume resistivity | | IEC 60093 | 1.0E+17 ohms·cm |
| dielectric strength | | IEC 60243-1 | 35 KV/mm |
| relative permittivity | | IEC 60250 | 2.90 |
| relative permittivity | | IEC 60250 | 2.80 |
| Dissipation Factor | | IEC 60250 | 1.0E-3 |
| Dissipation Factor | | IEC 60250 | 9.0E-3 |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | V |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | V |
| injection | Test Condition | Test Method | Test Result |
|---|
| Drying Temperature - Dry Air Dryer | | | 130 °C |
| Drying time - Dry Air Dryer | | | 2.0 to 4.0 hr |
| Suggested maximum moisture content | | | < 0.020 % |
| Suggested injection volume | | | 30 to 70 % |
| Temperature at the rear of the barrel | | | 315 to 325 °C |
| Temperature in the middle of the barrel | | | 320 to 330 °C |
| Temperature at the front of the material cylinder | | | 325 to 335 °C |
| Spray nozzle temperature | | | 315 to 340 °C |
| Processing (melt) temperature | | | 330 to 340 °C |
| Temperature | | | 110 to 150 °C |
| Back pressure | | | 10.0 to 20.0 Mpa |
| Exhaust hole depth | | | 0.025 to 0.050 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ISO 75-2/B | 191 °C |
| Heat distortion temperature | | ISO 75-2/A | 172 °C |
| vicat | | ISO 306/B120 | 202 °C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 6.5E-5 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 6.5E-5 cm/cm/°C |
| RTI Elec | | UL 746 | 150 °C |
| RTI Imp | | UL 746 | 130 °C |
| RTI | | UL 746 | 150 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices