Technical Data Sheet
| 物理性能 | Test Condition | Test Method | Test Result |
|---|
| 熔体质量流动速率 | 337°C/6.6 kg | ASTM D1238 | 18 g/10 min |
| 收缩率 - 流动 | 3.20 mm | 内部方法 | 0.50 到 0.70 % |
| 吸水率 | 24 hr | ASTM D570 | 0.25 % |
| 吸水率 | 平衡, 23°C | ASTM D570 | 1.3 % |
| 热性能 | Test Condition | Test Method | Test Result |
|---|
| 载荷下热变形温度 | 0.45 MPa, 未退火, 6.40 mm | ASTM D648 | 207 °C |
| 载荷下热变形温度 | 1.8 MPa, 未退火, 6.40 mm | ASTM D648 | 198 °C |
| 维卡软化温度 | | ASTM D15255 | 218 °C |
| 线形热膨胀系数 - 流动 | -20 到 150°C | ASTM E831 | 5.6E-5 cm/cm/°C |
| 导热系数 | | ASTM C177 | 0.22 W/m/K |
| RTI Elec | | UL 746 | 170 °C |
| RTI Imp | | UL 746 | 170 °C |
| RTI | | UL 746 | 170 °C |
| 可燃性 | Test Condition | Test Method | Test Result |
|---|
| UL阻燃等级 | 0.75 mm | UL 94 | V-0 |
| UL阻燃等级 | 3.0 mm | UL 94 | 5VA |
| 极限氧指数 | | ASTM D2863 | 44 % |
| 机械性能 | Test Condition | Test Method | Test Result |
|---|
| 拉伸模量 2 | | ASTM D638 | 3580 Mpa |
| 抗张强度 | 屈服 | ASTM D638 | 110 Mpa |
| 伸长率 3 | 屈服 | ASTM D638 | 7.0 % |
| 伸长率 3 | 断裂 | ASTM D638 | 60 % |
| 弯曲模量 | 100 mm 跨距 | ASTM D790 | 3510 Mpa |
| 弯曲强度 | 屈服, 100 mm 跨距 | ASTM D790 | 165 Mpa |
| 泰伯耐磨性 | 1000 Cycles, 1000 g, CS-17 转轮 | ASTM D1044 | 10.0 mg |
| 电气性能 | Test Condition | Test Method | Test Result |
|---|
| 体积电阻率 | | ASTM D257 | 1.0E+17 ohms·cm |
| 介电强度 | 1.60 mm, in Air | ASTM D149 | 33 KV/mm |
| 介电强度 | 1.60 mm, in Oil | ASTM D149 | 28 KV/mm |
| 介电常数 | 1 kHz | ASTM D150 | 3.15 |
| 耗散因数 | 1 kHz | ASTM D150 | 1.3E-3 |
| 耗散因数 | 2.45 GHz | ASTM D150 | 2.5E-3 |
| 耐电弧性 6 | | ASTM D495 | PLC 5 |
| 相比耐漏电起痕指数(CTI) | | UL 746 | PLC 4 |
| 高电弧燃烧指数(HAI) | | UL 746 | PLC 3 |
| 高电压电弧起痕速率(HVTR) | | UL 746 | PLC 2 |
| 热丝引燃(HWI) | | UL 746 | PLC 1 |
| 注射 | Test Condition | Test Method | Test Result |
|---|
| 干燥温度 | | | 150 °C |
| 干燥时间 | | | 4.0 到 6.0 hr |
| 建议的最大水分含量 | | | 0.020 % |
| 建议注射量 | | | 40 到 60 % |
| 料筒后部温度 | | | 330 到 400 °C |
| 料筒中部温度 | | | 340 到 400 °C |
| 料筒前部温度 | | | 345 到 400 °C |
| 射嘴温度 | | | 345 到 400 °C |
| 加工（熔体）温度 | | | 350 到 400 °C |
| 模具温度 | | | 135 到 165 °C |
| 背压 | | | 0.300 到 0.700 Mpa |
| 螺杆转速 | | | 40 到 70 rpm |
| 排气孔深度 | | | 0.025 到 0.076 mm |
| 硬度 | Test Condition | Test Method | Test Result |
|---|
| 洛氏硬度 | M 级 | ASTM D785 | 109 |
| 冲击性能 | Test Condition | Test Method | Test Result |
|---|
| 无缺口悬臂梁冲击 | 23°C | ASTM D4812 | 1300 J/m |
| 反向缺口冲击 | 3.20 mm | ASTM D256 | 1200 J/m |
| 落锤冲击 | 23°C | ASTM D3029 | 33.0 J |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices