PEEK 450GL20 VICTREX UK

Form：Granules | Grade：Injection grade

Properties:

high strengthGlass fiber reinforced

Typical Applications:

Non specific foodMedical suppliesNursing supplies

Supplier(1)

Product Description

Certificates(1)

Datasheet

Product Description

Typical Applications:	Non specific food \| Medical supplies \| Nursing supplies
Properties:	high strength \| Glass fiber reinforced

Certificates

Technical Data Sheet

Filling analysis	Test Condition	Test Method	Test Result	Test Unit
Melt viscosity	400°C	ISO 11443	475	Pa·s
impact performance	Test Condition	Test Method	Test Result	Test Unit
Suspended wall beam without notch impact strength	23°C	ISO 180	65	kJ/m²
Impact strength of cantilever beam gap	23°C	ISO 180/A	10	kJ/m²
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Bending modulus	23°C	ISO 178	8300	Mpa
bending strength	23°C	ISO 178	250	Mpa
Tensile modulus	23°C	ISO 527-2	8800	Mpa
tensile strength	Break,23°C	ISO 527-2	160	Mpa
Tensile strain	Break,23°C	ISO 527-2	3.4	%
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Linear coefficient of thermal expansion	MD:>143°C	ISO 11359-2	2.2E-05	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	MD:<143°C	ISO 11359-2	2E-05	cm/cm/°C
Melting temperature		ISO 11357-3	343	°C
Glass transition temperature	--8	ISO 11357-2	150	°C
Glass transition temperature	Glass transition temperature	--7	ISO 11357-2	143	°C
Hot deformation temperature	1.8MPa,Unannealed	ISO 75-2/Af	315	°C
thermal conductivity	23°C10	ISO 22007-4	0.35	W/m/K
thermal conductivity	thermal conductivity	23°C9	ISO 22007-4	0.30	W/m/K
Linear coefficient of thermal expansion	TD:>143°C	ISO 11359-2	1.2E-04	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	TD:<143°C	ISO 11359-2	4.5E-05	cm/cm/°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Spiral flow length		Internal Method	10.0	CM
Shrinkage rate	TD	ISO 294-4	0.90	%
Shrinkage rate	Shrinkage rate	MD	ISO 294-4	0.30	%
Water absorption rate	Saturation,23°C	ISO 62	0.40	%
Water absorption rate	Water absorption rate	100°C，Saturation	ISO 62	0.45	%
density	比重	ISO 1183	1.43	g/cm³
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Dielectric constant	23°C,1kHz	IEC 60250	3.10
Dissipation factor	23°C,1MHz	IEC 60250	5E-03
Dielectric strength	2.00mm	IEC 60243-1	24	KV/mm
Volume resistivity		IEC 60093	1E+16	ohms·cm
hardness	Test Condition	Test Method	Test Result	Test Unit
Shore hardness	ShoreD,23°C	ISO 868	86

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top