Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTM D1238 | 5.6 g/10 min |
| melt mass-flow rate | | ISO 1133 | 18 g/10 min |
| Shrinkage rate | | 内部方法 | 0.50 - 0.80 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 112 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 2270 Mpa |
| Tensile modulus | | ISO 527-2/1 | 2370 Mpa |
| tensile strength | | ASTM D638 | 44.0 Mpa |
| tensile strength | | ISO 527-2/50 | 47.0 Mpa |
| tensile strength | | ASTM D638 | 33.0 Mpa |
| tensile strength | | ISO 527-2/50 | 35.0 Mpa |
| elongation | | ASTM D638 | 2.0 % |
| elongation | | ISO 527-2/50 | 2.6 % |
| elongation | | ASTM D638 | 24 % |
| elongation | | ISO 527-2/50 | 25 % |
| Flexural modulus | | ASTM D790 | 2300 Mpa |
| Flexural modulus | | ISO 178 | 2200 Mpa |
| bending strength | | ISO 178 | 70.0 Mpa |
| bending strength | | ASTM D790 | 70.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ISO 179/1eA | 9.0 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179/1eA | 26 kJ/m² |
| Dart impact | | ASTM D3763 | 30.0 J |
| Filling analysis | Test Condition | Test Method | Test Result |
|---|
| melt viscosity | | ASTM D3835 | 225 Pa·s |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| arc resistance | | ASTM D495 | PLC 6 |
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 0 |
| High arc combustion index (HAI) | | UL 746 | PLC 0 |
| High Voltage Arc Traceability Rate (HVTR) | | UL 746 | PLC 3 |
| Hot wire ignition (HWI) | | UL 746 | PLC 3 |
| injection | Test Condition | Test Method | Test Result |
|---|
| drying temperature | | | 80 to 95 °C |
| drying time | | | 2.0 to 4.0 hr |
| Suggested maximum moisture content | | | 0.10 % |
| Suggested injection volume | | | 50 to 70 % |
| Temperature at the rear of the barrel | | | 190 to 210 °C |
| Temperature in the middle of the barrel | | | 205 to 225 °C |
| Temperature at the front of the material cylinder | | | 215 to 240 °C |
| Spray nozzle temperature | | | 220 to 260 °C |
| Processing (melt) temperature | | | 220 to 260 °C |
| Temperature | | | 50 to 70 °C |
| Back pressure | | | 0.300 to 0.700 Mpa |
| screw speed | | | 30 to 60 rpm |
| Exhaust hole depth | | | 0.038 to 0.051 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 94.0 °C |
| Heat distortion temperature | | ASTM D648 | 80.0 °C |
| Heat distortion temperature | | ISO 75-2/Af | 81.0 °C |
| vicat | | ASTM D15258 | 99.0 °C |
| vicat | | ISO 306/B50 | 98.0 °C |
| vicat | | ISO 306/B120 | 100 °C |
| Linear coefficient of thermal expansion | | ASTM E831 | 8.8E-5 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTM E831 | 8.8E-5 cm/cm/°C |
| RTI Elec | | UL 746 | 60.0 °C |
| RTI Imp | | UL 746 | 60.0 °C |
| RTI | | UL 746 | 60.0 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices