PA66 D.AKV30H2.0 BK LANXESS USA

Form：Granules | Grade：Injection grade

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Certificates

No Data...

Technical Data Sheet

impact performance	Test Condition	Test Method	Test Result	Test Unit
Suspended wall beam without notch impact strength	23°C	ISO 180/1U	60	kJ/m²
Suspended wall beam without notch impact strength	Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	55	kJ/m²
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	75	kJ/m²
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	60	kJ/m²
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	3.2mm	UL 94	HB
Burning wire flammability index	0.8mm	IEC 60695-2-12	700	°C
UL flame retardant rating	0.75mm	UL 94	HB
	UL flame retardant rating	1.5mm	UL 94	HB
		UL flame retardant rating	1.6mm	UL 94	HB
		UL flame retardant rating	UL flame retardant rating	3.0mm	UL 94	HB
Burning wire flammability index	1.6mm	IEC 60695-2-12	700	°C
Burning wire flammability index	Burning wire flammability index	3.0mm	IEC 60695-2-12	700	°C
Extreme Oxygen Index		ISO 4589-2	23	%
BurningBehavior	>1.00mm	ISO 3795	passed
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
bending strength	FlexuralStrainatFlexuralStrength6(23°C)		4.0	%
	bending strength	23°C	ISO 178	270	Mpa
		bending strength	3.5%Strain	ISO 178/A	265	Mpa
		bending strength	bending strength	23°C	ASTM D790	270	Mpa
Tensile modulus	23°C	ASTM D638	9170	Mpa
Tensile modulus	Tensile modulus	23°C	ISO 527-2/1	10000	Mpa
tensile strength	Break,23°C	ASTM D638	170	Mpa
tensile strength	tensile strength	Break,23°C	ISO 527-2/5	175	Mpa
elongation	Break,23°C	ASTM D638	3.0	%
Tensile strain	Break,23°C	ISO 527-2/5	3.0	%
Nominal tensile fracture strain	23°C	ISO 527-2/50	4.4	%
Bending modulus	23°C	ASTM D790	8690	Mpa
Bending modulus	Bending modulus	23°C	ISO 178/A	9200	Mpa
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45MPa,Unannealed	ISO 75-2/B	250	°C
	Hot deformation temperature	1.8MPa,Unannealed,4.00mm	ASTM D648	>249	°C
	Hot deformation temperature	Hot deformation temperature	0.45MPa,Unannealed,4.00mm	ASTM D648	>249	°C
Melting temperature		ISO 11357-3	263	°C
Ball Pressure Test	253°C	IEC 60695-10-2	Pass
Vicat softening temperature	--	ISO 306/B120	>230	°C
Vicat softening temperature	Vicat softening temperature	--	ISO 306/B50	230	°C
Hot deformation temperature	1.8MPa,Unannealed	ISO 75-2/A	>240	°C
Linear coefficient of thermal expansion	MD：23to55°C	ISO 11359-2	3E-05	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	TD：23to55°C	ISO 11359-2	9E-05	cm/cm/°C
RTI Elec	0.75mm	UL 746	125	°C
RTI Elec	RTI Elec	1.5mm	UL 746	125	°C
RTI Imp	0.75mm	UL 746	90.0	°C
RTI Imp	RTI Imp	1.5mm	UL 746	105	°C
RTI Str	0.75mm	UL 746	110	°C
RTI Str	RTI Str	1.5mm	UL 746	115	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Water absorption rate	Saturation,23°C	ISO 62	5.5	%
Shrinkage rate	MD:120°C,2hr,2.00mm3	ISO 294-4	0.070	%
	Shrinkage rate	MD:290°C,2.00mm2	ISO 294-4	0.39	%
		Shrinkage rate	TD:120°C,2hr,2.00mm3	ISO 294-4	0.13	%
		Shrinkage rate	Shrinkage rate	TD:290°C,2.00mm2	ISO 294-4	0.93	%
Apparent density		ISO 60	0.70	g/cm³
Water absorption rate	Equilibrium,23°C,50%RH	ISO 62	2.0	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Surface resistivity		IEC 60093	1E+15	ohms
Volume resistivity	23°C	IEC 60093	1E+15	ohms·cm
Dielectric strength	23°C,1.00mm	IEC 60243-1	35	KV/mm
Dielectric strength	Dielectric strength	23°C,3.00mm	IEC 60243-1	30	KV/mm
Dielectric constant	23°C,50Hz	IEC 60250	4.00
Dielectric constant	Dielectric constant	23°C,1MHz	IEC 60250	4.00
Relative permittivity	23°C,100Hz	IEC 60250	4.00
Relative permittivity	Relative permittivity	23°C,1MHz	IEC 60250	4.00
Dissipation factor	23°C,50Hz	IEC 60250	0.012
	Dissipation factor	23°C,100Hz	IEC 60250	0.012
	Dissipation factor	Dissipation factor	23°C,1MHz	IEC 60250	0.0190.019
hardness	Test Condition	Test Method	Test Result	Test Unit
Ball Pressure Test		ISO 2039-1	220	Mpa
film	Test Condition	Test Method	Test Result	Test Unit
Thin film puncture strength	--8	ISO 6603-2	800	N
	Thin film puncture strength	--7	ISO 6603-2	900	N
		Thin film puncture strength	--8	ISO 6603-2	2.30	J
		Thin film puncture strength	Thin film puncture strength	--7	ISO 6603-2	2.80	J
Supplementary Information	Test Condition	Test Method	Test Result	Test Unit
ISO Shortcut		ISO 1874	PA66.GHR.14-100.GF30

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top