PC 141R-111 SABIC INNOVATIVE SPAIN

104

Form：Granules | Grade：Injection grade

Properties:

transparentFlame retardant

Supplier(1)

Product Description

Certificates(1)

Datasheet

Alternative(26)

Product Description

Properties:

transparent | Flame retardant

Certificates

Technical Data Sheet

optical performance	Test Condition	Test Method	Test Result	Test Unit
Refractive index		ASTM D542	1.586
transmissivity	2540μm	ASTM D1003	88.0	%
turbidity	2540μm	ASTM D1003	1.0	%
impact performance	Test Condition	Test Method	Test Result	Test Unit
Suspended wall beam without notch impact strength	23°C	ASTM D4812	3200	J/m
Dart impact	23°C,TotalEnergy	ASTM D3763	63.8	J
Dart impact	Dart impact	23°C	ASTM D3029	169	J
Impact strength of cantilever beam gap		ASTM D1822	578	kJ/m²
Impact strength of cantilever beam gap	Impact strength of cantilever beam gap	23°C	ASTM D256	800	J/m
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	0.71mm	UL 94	HB
Radiation board grade	UL		YES
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
tensile strength	Yield	ASTM D638	62.1	Mpa
tensile strength	tensile strength	Break	ASTM D638	68.9	Mpa
elongation	Yield	ASTM D638	7.0	%
elongation	elongation	Break	ASTM D638	130	%
Bending modulus	50.0mmSpan	ASTM D790	2340	Mpa
bending strength	Yield,50.0mmSpan	ASTM D790	96.5	Mpa
Taber abraser	1000Cycles,1000g,CS-17Wheel	ASTM D1044	10.0	mg
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45MPa,Unannealed,6.40mm	ASTM D648	138	°C
Hot deformation temperature	Hot deformation temperature	1.8MPa,Unannealed,6.40mm	ASTM D648	132	°C
Vicat softening temperature		ASTM D15256	154	°C
Linear coefficient of thermal expansion	MD：-40to95°C	ASTME831	6.8E-05	cm/cm/°C
specific heat		ASTMC351	1260	J/kg/°C
thermal conductivity		ASTMC177	0.27	W/m/K
RTI Elec		UL 746	130	°C
RTI Imp		UL 746	130	°C
RTI		UL 746	130	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Water absorption rate	Equilibrium,23°C	ASTM D570	0.35	%
Water absorption rate	Water absorption rate	Equilibrium,100°C	ASTM D570	0.58	%
Outdoor applicability		UL 746C	f2
density	--	ASTM D792	1.20	g/cm³
density	density	--	ASTM D792	1.19	g/cm³
Specific volume		ASTM D792	0.835	cm³/g
melt mass-flow rate	300°C/1.2kg	ASTM D1238	11	g/10min
Shrinkage rate	MD：3.20mm	Internal Method	0.50-0.70	%
Water absorption rate	24hr	ASTM D570	0.15	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Dielectric constant	1MHz	ASTM D150	2.96
Dissipation factor	50Hz	ASTM D150	9E-04
	Dissipation factor	60Hz	ASTM D150	9E-04
	Dissipation factor	Dissipation factor	1MHz	ASTM D150	0.010
Compared to the anti leakage trace index	CTI	UL 746	PLC 2
High arc combustion index	HAI	UL 746	PLC 1
High voltage arc tracing rate	HVTR	UL 746	PLC 2
Hot wire ignition	HWI	UL 746	PLC 2
Volume resistivity		ASTM D257	>1.0E+17	ohms·cm
Dielectric strength	3.20mm,inAir	ASTM D149	15	KV/mm
Dielectric constant	50Hz	ASTM D150	3.17
Dielectric constant	Dielectric constant	60Hz	ASTM D150	3.17
hardness	Test Condition	Test Method	Test Result	Test Unit
Rockwell hardness	M-Scale	ASTM D785	70
Rockwell hardness	Rockwell hardness	R-Scale	ASTM D785	118

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top