PC APEC 2097 COVESTRO GERMANY

Form：Granules | Grade：Injection grade

Properties:

UV curingGood demolding performancHigh temperature resistanHigh mobility

Typical Applications:

Automotive sectorCastersMedical suppliesNursing supplies

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Typical Applications:	Automotive sector \| Casters \| Medical supplies \| Nursing supplies
Properties:	UV curing \| Good demolding performanc \| High temperature resistan \| High mobility

Certificates

No Data...

Technical Data Sheet

optical performance	Test Condition	Test Method	Test Result	Test Unit
Refractive index		ISO 489	1.566
transmissivity	1000 μm	ISO 13468-2	89.0	%
Electrolytic corrosion	23°C	IEC 60426	A1
impact performance	Test Condition	Test Method	Test Result	Test Unit
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	1.5 mm	UL 94	HB
Burning wire flammability index		IEC 60695-2-12	800	°C
Extreme Oxygen Index		ISO 4589-2	25	%
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile modulus	23°C	ISO 527-2/1	2450	Mpa
tensile strength	Yield, 23°C	ISO 527-2/50	76.0	Mpa
Tensile strain	Yield, 23°C	ISO 527-2/50	6.9	%
Nominal tensile fracture strain	23°C	ISO 527-2/50	> 50	%
Bending modulus	23°C	ISO 178	2450	Mpa
bending strength	23°C	ISO 178	110	Mpa
injection	Test Condition	Test Method	Test Result	Test Unit
Drying Temperature - Dry Air Dryer			130	°C
Drying time - Dry Air Dryer			2.0 to 4.0	hr
Suggested maximum moisture content			< 0.020	%
Suggested injection volume			30 to 70	%
Temperature at the rear of the barrel			315 to 325	°C
Temperature in the middle of the barrel			320 to 330	°C
Temperature at the front of the material cylinder			325 to 335	°C
Spray nozzle temperature			315 to 340	°C
Processing (melt) temperature			330 to 340	°C
Mold temperature			110 to 150	°C
Back pressure			10.0 to 20.0	Mpa
Exhaust hole depth			0.025 to 0.050	mm
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45 MPa, Unannealed	ISO 75-2/B	191	°C
Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed	ISO 75-2/A	172	°C
Vicat softening temperature		ISO 306/B120	202	°C
Linear coefficient of thermal expansion	Flow : 23 to 55°C	ISO 11359-2	6.5E-5	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Across Flow : 23 to 55°C	ISO 11359-2	6.5E-5	cm/cm/°C
RTI Elec		UL 746	150	°C
RTI Imp		UL 746	130	°C
RTI		UL 746	150	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
density	23°C	ISO 1183	1.13	g/cm³
melt mass-flow rate	330°C/2.16 kg	ISO 1133	8.0	g/10 min
Melt Volume Flow Rate (MVR)	330°C/2.16 kg	ISO 1133	8.00	cm3/10min
Shrinkage rate	横向Flow : 2.00 mm	ISO 294-4	0.90	%
Shrinkage rate	Shrinkage rate	Flow : 2.00 mm	ISO 294-4	0.90	%
Water absorption rate	Saturation, 23°C	ISO 62	0.30	%
Water absorption rate	Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	0.12	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Surface resistivity		IEC 60093	1.0E+16	ohms
Volume resistivity	23°C	IEC 60093	1.0E+17	ohms·cm
Dielectric strength	23°C, 1.00 mm	IEC 60243-1	35	KV/mm
Relative permittivity	23°C, 100 Hz	IEC 60250	2.90
Relative permittivity	Relative permittivity	23°C, 1 MHz	IEC 60250	2.80
Dissipation factor	23°C, 100 Hz	IEC 60250	1.0E-3
Dissipation factor	Dissipation factor	23°C, 1 MHz	IEC 60250	9.0E-3
Compared to the anti leakage trace index	Solution A	IEC 60112	PLC 0
Compared to the anti leakage trace index	Compared to the anti leakage trace index	Solution B	IEC 60112	PLC 4
hardness	Test Condition	Test Method	Test Result	Test Unit
Ball Pressure Test		ISO 2039-1	130	Mpa

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top