PBT DR48-BK1066 SABIC INNOVATIVE SHANGHAI

Form：Granules | Grade：Injection grade

Properties:

Flame retardantGlass fiber reinforced

Typical Applications:

Side track applicationNon specific foodLawn equipmentGarden equipmentIndustrial applicationsAutomotive External PartsElectrical fieldElectronic fieldArchitectural application fieldOutdoor applicationsElectrical appliancesEngine hood partsMedical suppliesNursing suppliesPlastic bagAutomotive interior partsCasters

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Typical Applications:	Side track application \| Non specific food \| Lawn equipment \| Garden equipment \| Industrial applications \| Automotive External Parts \| Electrical field \| Electronic field \| Architectural application field \| Outdoor applications \| Electrical appliances \| Engine hood parts \| Medical supplies \| Nursing supplies \| Plastic bag \| Automotive interior parts \| Casters
Properties:	Flame retardant \| Glass fiber reinforced

Certificates

No Data...

Technical Data Sheet

impact performance	Test Condition	Test Method	Test Result	Test Unit
Suspended wall beam without notch impact strength	23°C	ASTM D4812	500	J/m
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	0.9 mm	UL 94	V-0
UL flame retardant rating	UL flame retardant rating	3.0 mm	UL 94	5VA
Extreme Oxygen Index		ASTM D2863	29	%
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
tensile strength	Break	ASTM D638	93.0	Mpa
Bending modulus	50.0 mm Span	ASTM D790	5200	Mpa
bending strength	Break, 50.0 mm Span	ASTM D790	140	Mpa
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			120	°C
drying time			3.0 to 4.0	hr
Suggested maximum moisture content			0.020	%
Suggested injection volume			40 to 80	%
Temperature at the rear of the barrel			240 to 255	°C
Temperature in the middle of the barrel			245 to 260	°C
Temperature at the front of the material cylinder			250 to 265	°C
Spray nozzle temperature			245 to 260	°C
Processing (melt) temperature			250 to 265	°C
Mold temperature			65 to 90	°C
Back pressure			0.300 to 0.700	Mpa
Screw speed			50 to 80	rpm
Exhaust hole depth			0.025 to 0.038	mm
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45 MPa, Unannealed, 6.40 mm	ASTM D648	210	°C
Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed, 6.40 mm	ASTM D648	182	°C
Linear coefficient of thermal expansion	-40 to 40°C，Flow	ASTM E831	2.0E-5	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	60 to 138°C，Flow	ASTM E831	2.0E-5	cm/cm/°C
RTI Elec		UL 746	120	°C
RTI Imp		UL 746	120	°C
RTI		UL 746	140	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Specific volume		ASTM D792	0.650	cm³/g
Shrinkage rate	Flow : 1.50 to 3.20 mm	Internal Method	0.40 - 0.60	%
	Shrinkage rate	Flow : 3.20 to 4.60 mm	Internal Method	0.60 - 0.90	%
		Shrinkage rate	Across FlowFlow : 1.50 to 3.20 mm	Internal Method	0.50 - 0.80	%
		Shrinkage rate	Shrinkage rate	Across FlowFlow : 3.20 to 4.60 mm	Internal Method	0.80 - 1.1	%
Water absorption rate	24 hr	ASTM D570	0.070	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Volume resistivity		ASTM D257	1.0E+15	ohms·cm
Dielectric strength	1.60 mm, in Oil	ASTM D149	25	KV/mm
Dielectric strength	Dielectric strength	3.20 mm, in Air	ASTM D149	19	KV/mm
Dielectric constant	100 Hz	ASTM D150	3.60
Dielectric constant	Dielectric constant	1 MHz	ASTM D150	3.40
Dissipation factor	100 Hz	ASTM D150	2.0E-3
Dissipation factor	Dissipation factor	1 MHz	ASTM D150	0.016
Arc resistance		ASTM D495	PLC 6
Compared to the anti leakage trace index		UL 746	PLC 3
High arc combustion index		UL 746	PLC 0
High voltage arc tracing rate		UL 746	PLC 4
Hot wire ignition		UL 746	PLC 3
hardness	Test Condition	Test Method	Test Result	Test Unit
Rockwell hardness	R-Scale	ASTM D785	118

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top