Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| density | | ASTM D792/ISO 1183 | 1.06 | |
| Shrinkage rate | | ASTM D955 | 1.3~1.4 | % |
| Water absorption rate 23 ℃/24h | | ASTM D570/ISO 62 | 1.3 | % |
| MediumDensity | | | 0.900 | g/cm³ |
| SpecificHeatCapacity of Melt | | | 2800 | J/kg/°C |
| ThermalConductivityofMelt | | | 0.19 | W/m/K |
| Stickiness number | 96%H2SO4 | ISO307 | 120 | cm³/g |
| Shrinkage rate | MD：3.20mm | | 1.1 | % |
| Shrinkage rate | TD：3.20mm | | 1.1 | % |
| Shrinkage rate | TD | ISO294-4 | 1.5 | % |
| Shrinkage rate | MD | ISO294-4 | 1.5 | % |
| Water absorption rate | 饱和,23°C,2.00mm | ISO62 | 3.0 | % |
| Water absorption rate | 平衡,23°C,2.00mm,50%RH | ISO62 | 1.3 | % |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile modulus | | ISO527-2 | 2400 | Mpa |
| tensile strength | 屈服 | ISO527-2 | 62.0 | Mpa |
| elongation | 屈服 | ISO527-2 | 4.3 | % |
| Nominal tensile fracture strain | | ISO527-2 | 35 | % |
| Rockwell hardness | R级 | ISO2039-2 | 114 | |
| elongation at break | | ASTM D412/ISO 527 | 35 | % |
| Tensile modulus | | ASTM D412/ISO 527 | 2050 | kg/cm²(MPa)[Lb/in²] |
| tensile strength | | ASTM D412/ISO 527 | 62 | kg/cm²(MPa)[Lb/in²] |
| Impact strength of simply supported beam without notch | -30°C | ISO179/1eU | NoBreak | |
| Impact strength of simply supported beam without notch | 23°C | ISO179/1eU | NoBreak | |
| Charpy impact strength | | ASTM D256/ISO 179 | 4 | kg·cm/cm(J/M)ft·lb/in |
| Charpy impact strength | | ASTM D256/ISO 179 | NB | kg·cm/cm(J/M)ft·lb/in |
| Charpy impact strength | | ASTM D256/ISO 179 | 5 | kg·cm/cm(J/M)ft·lb/in |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Combustibility (rate) | | UL94 | HB | |
| Hot deformation temperature | | ASTM D648/ISO 75 | 135 | ℃（℉） |
| Hot deformation temperature | | ASTM D648/ISO 75 | 62 | ℃（℉） |
| melting point | | | 218 | ℃（℉） |
| Linear coefficient of thermal expansion | | ASTM D696/ISO 11359 | 0.9~1.8 | |
| Hot deformation temperature | 0.45MPa,未退火 | ISO75-2/B | 135 | °C |
| Hot deformation temperature | 1.8MPa,未退火 | ISO75-2/A | 62.0 | °C |
| Glass transition temperature | | ISO11357-2 | 60.0 | °C |
| vicat softening point | | ISO306/B50 | 180 | °C |
| Melting temperature | | ISO11357-3 | 218 | °C |
| Linear coefficient of thermal expansion | MD | ISO11359-2 | 1.2E-04 | cm/cm/°C |
| Linear coefficient of thermal expansion | TD | ISO11359-2 | 1.2E-04 | cm/cm/°C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Volume resistivity | | IEC60093 | >1.0E+15 | ohms·cm |
| Dielectric strength | | IEC60243-1 | 36 | KV/mm |
| Relative permittivity | 100Hz | IEC60250 | 3.60 | |
| Relative permittivity | 1MHz | IEC60250 | 3.20 | |
| Dissipation factor | 100Hz | IEC60250 | 0.014 | |
| Dissipation factor | 1MHz | IEC60250 | 0.017 | |
| film | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile strain MD | Yield | ISO527-3 | 4.3 | % |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| Burning rate | 1.00mm | ISO3795 | <100 | mm/min |
| UL flame retardant rating | 0.9mm | UL94 | HB | |
| UL flame retardant rating | 1.5mm | UL94 | HB | |
| UL flame retardant rating | 0.9mm | IEC60695-11-10,-20 | HB | |
| UL flame retardant rating | 1.5mm | IEC60695-11-10,-20 | HB | |
| Extreme Oxygen Index | | ISO4589-2 | 25 | % |
| FMVSS flammability | | FMVSS302 | B | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare