Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Shrinkage rate | 流动 : 3.20 mm | 内部方法 | 0.50 到 0.70 | % |
| Shrinkage rate | 横向流动 : 3.20 mm | 内部方法 | 0.50 到 0.70 | % |
| Water absorption rate | 24 hr | ASTM D570 | 0.10 | % |
| Water absorption rate | 平衡, 23°C | ASTM D570 | 0.40 | % |
| Melt mass flow rate | 260°C/5.0 kg | ASTM D1238 | 17 | g/10 min |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Dart impact equipped with measuring instruments | -30°C, Total Energy | ASTM D3763 | 33.0 | J |
| Dart impact equipped with measuring instruments | 23°C, Total Energy | ASTM D3763 | 40.0 | J |
| tensile strength | 屈服 | ASTM D638 | 54.0 | Mpa |
| elongation | 断裂 | ASTM D638 | 75 | % |
| Rockwell hardness | R 级 | ASTM D785 | 118 | |
| Bending modulus | 50.0 mm 跨距 | ASTM D790 | 2300 | Mpa |
| bending strength | 屈服, 50.0 mm 跨距 | ASTM D790 | 84.0 | Mpa |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| vicat softening point | | ASTM D15254 | 129 | °C |
| Linear coefficient of thermal expansion | 流动 : -20 到 150°C | ASTM E831 | 7.2E-5 | cm/cm/°C |
| Linear coefficient of thermal expansion | 横向 : -20 到 150°C | ASTM E831 | 7.2E-5 | cm/cm/°C |
| thermal conductivity | | ASTM C177 | 0.20 | W/m/K |
| RTI | | UL 746 | 60.0 | °C |
| RTI Imp | | UL 746 | 60.0 | °C |
| RTI Elec | | UL 746 | 60.0 | °C |
| Hot deformation temperature | 0.45 MPa, 未退火, 3.20 mm | ASTM D648 | 123 | °C |
| Hot deformation temperature | 0.45 MPa, 未退火, 6.40 mm | ASTM D648 | 129 | °C |
| Hot deformation temperature | 1.8 MPa, 未退火, 3.20 mm | ASTM D648 | 107 | °C |
| Hot deformation temperature | 1.8 MPa, 未退火, 6.40 mm | ASTM D648 | 110 | °C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Compared to the Leakage Tracking Index (CTI) | | UL 746 | PLC 2 | |
| Hot wire ignition (HWI) | | UL 746 | PLC 2 | |
| High arc combustion index (HAI) | | UL 746 | PLC 0 | |
| Arc resistance | | ASTM D495 | PLC 6 | |
| injection | Test Condition | Test Method | Test Result | Unit |
|---|
| drying temperature | | | 105 到 110 | °C |
| Suggested maximum moisture content | | | 0.040 | % |
| Processing (melt) temperature | | | 275 到 300 | °C |
| Mold temperature | | | 60 到 90 | °C |
| drying time | | | 3.0 到 4.0 | hr |
| Suggested injection volume | | | 30 到 80 | % |
| Temperature at the rear of the barrel | | | 250 到 290 | °C |
| Temperature in the middle of the barrel | | | 255 到 295 | °C |
| Temperature at the front of the material cylinder | | | 260 到 300 | °C |
| Spray nozzle temperature | | | 275 到 300 | °C |
| Back pressure | | | 0.300 到 0.700 | Mpa |
| Screw speed | | | 40 到 70 | rpm |
| Exhaust hole depth | | | 0.038 到 0.076 | mm |
| optical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| gloss | 60°, 无织构 | ASTM D523 | 30 | |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| UL flame retardant rating | 1.5 mm | UL 94 | HB | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices