PC Makrolon® AL2447
26
- Properties:High impact resistanceFlame retardant
- Usages:Automotive ApplicationsCasters
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Apparent density 3 | ISO60 | 0.66 g/cm³ | |
| melt mass-flow rate | ISO1133 | 20 g/10min | |
| Melt volume flow rate | ISO1133 | 19.0 cm3/10min | |
| Shrinkage rate | ISO2577 | 0.50到0.70 % | |
| ISO2577 | 0.50到0.70 % | ||
| ISO294-4 | 0.70 % | ||
| ISO294-4 | 0.65 % | ||
| Water absorption rate | ISO62 | 0.30 % | |
| ISO62 | 0.12 % |
| hardness | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ISO2039-1 | 115 Mpa |
| optical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| refractive index | ISO489 | 1.586 | |
| transmissivity | ISO13468-2 | 89.0 % | |
| ISO13468-2 | 89.0 % | ||
| ISO13468-2 | 88.0 % | ||
| ISO13468-2 | >87.0 % | ||
| Haze ratio | ISO14782 | <0.50 % |
| flammability | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Extreme Oxygen Index 11 | ISO4589-2 | 28 % | |
| FlashIgnitionTemperature | ASTMD1929 | 480 °C | |
| SelfIgnitionTemperature | ASTMD1929 | 550 °C | |
| UL flame retardant rating | UL94 | HB | |
| UL94 | V-2 |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ElectrolyticalCorrosion | IEC60426 | A1 |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Impact strength of simply supported beam without notch | ISO179/1eU | 无断裂 | |
| Impact strength of cantilever beam gap | ISO7391 | 15 kJ/m² | |
| ISO7391 | 65 kJ/m² | ||
| Multi axis Instrumented Impact Energy | ISO6603-2 | 65.0 J | |
| ISO6603-2 | 55.0 J | ||
| Multi axis Instrumented Peak Impact Force | ISO6603-2 | 6000 N | |
| ISO6603-2 | 5100 N | ||
| Impact strength of simply supported beam gap 7 | ISO7391 | 14 kJ/m² | |
| ISO7391 | 65 kJ/m² | ||
| Impact strength of simply supported beam without notch | ISO179/1eU | 无断裂 | |
| ISO179/1eU | 无断裂 |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Tensile modulus | ISO527-2/1 | 2400 Mpa | |
| Tensile stress | ISO527-2/50 | 66.0 Mpa | |
| ISO527-2/5 | 70.0 Mpa | ||
| ISO527-2/50 | 65.0 Mpa | ||
| Tensile strain | ISO527-2/50 | 6.0 % | |
| ISO527-2/5 | 130 % | ||
| ISO527-2/50 | 120 % | ||
| Nominal tensile fracture strain | ISO527-2/50 | >50 % | |
| Tensile creep modulus | ISO899-1 | 2200 Mpa | |
| ISO899-1 | 1900 Mpa | ||
| Flexural modulus | ISO178 | 2350 Mpa | |
| Bending stress 5 | ISO178 | 98.0 Mpa | |
| ISO178 | 74.0 Mpa | ||
| Bending strain 6 | ISO178 | 7.0 % |
| film | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Water vapor permeability | ISO15106-1 | 15 g/m²/24hr | |
| GasPermeation | ISO2556 | 18900 cm³/m²/bar/24hr | |
| ISO2556 | 4800 cm³/m²/bar/24hr | ||
| ISO2556 | 630 cm³/m²/bar/24hr | ||
| ISO2556 | 160 cm³/m²/bar/24hr | ||
| ISO2556 | 3150 cm³/m²/bar/24hr | ||
| ISO2556 | 800 cm³/m²/bar/24hr |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Surface Resistivity | IEC60093 | 1E+16 ohms | |
| Volume resistivity | IEC60093 | 1E+16 ohms·cm | |
| dielectric strength | IEC60243-1 | 34 KV/mm | |
| IEC60250 | 3.10 | ||
| IEC60250 | 3.00 | ||
| Dissipation Factor | IEC60250 | 5E-04 | |
| IEC60250 | 9E-03 | ||
| CTI | IEC60112 | 250 V | |
| IEC60112 | 125 V |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ISO75-2/B | 138 °C | ||
| ISO75-2/A | 125 °C | ||
| Glass transition temperature 9 | ISO11357-2 | 145 °C | |
| vicat | ISO306/B50 | 144 °C | |
| ISO306/B120 | 145 °C | ||
| BallPressure Test | IEC60695-10-2 | 通过 | |
| ISO11359-2 | 6.5E-05 cm/cm/°C | ||
| ISO11359-2 | 6.5E-05 cm/cm/°C | ||
| Thermal conductivity coefficient 10 | ISO8302 | 0.20 W/m/K | |
| RTI Elec | UL746 | 125 °C | |
| RTI Imp | UL746 | 115 °C | |
| RTI | UL746 | 125 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Contact Us
Get App
Top