PA66 R535H ASCEND USA

Form：Granules | Grade：Injection grade

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Certificates

No Data...

Technical Data Sheet

impact performance	Test Condition	Test Method	Test Result	Test Unit
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	80	kJ/m²
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	70	kJ/m²
flammability	Test Condition	Test Method	Test Result	Test Unit
Burning rate	2.00 mm, 自动灭火	ISO 3795	0.0	mm/min
UL flame retardant rating	0.75 mm	UL 94	HB
	UL flame retardant rating	1.5 mm	UL 94	HB
	UL flame retardant rating	UL flame retardant rating	3.0 mm	UL 94	HB
Burning wire flammability index	0.75 mm	IEC 60695-2-12	700	°C
	Burning wire flammability index	1.5 mm	IEC 60695-2-12	700	°C
	Burning wire flammability index	Burning wire flammability index	3.0 mm	IEC 60695-2-12	875	°C
Hot filament ignition temperature	0.75 mm	IEC 60695-2-13	725	°C
	Hot filament ignition temperature	1.5 mm	IEC 60695-2-13	725	°C
	Hot filament ignition temperature	Hot filament ignition temperature	3.0 mm	IEC 60695-2-13	750	°C
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Poisson's ratio		ISO 527	0.40
bending strength	23°C	ISO 178	300	Mpa
Bending modulus	23°C	ISO 178	10500	Mpa
Tensile strain	Break, 23°C	ISO 527-2	3.0	%
tensile strength	Break, 23°C	ISO 527-2	210	Mpa
Tensile modulus	23°C	ISO 527-2	11600	Mpa
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			80	°C
drying time			4.0	hr
Suggested maximum material return ratio			25	%
Temperature at the rear of the barrel			280 to 310	°C
Temperature in the middle of the barrel			280 to 310	°C
Temperature at the front of the material cylinder			280 to 310	°C
Spray nozzle temperature			280 to 310	°C
Processing (melt) temperature			285 to 305	°C
Mold temperature			65 to 95	°C
thermal performance	Test Condition	Test Method	Test Result	Test Unit
RTI	1.5 mm	UL 746	140	°C
	RTI	3.0 mm	UL 746	140	°C
	RTI	RTI	0.75 mm	UL 746	140	°C
RTI Imp	3.0 mm	UL 746	125	°C
	RTI Imp	1.5 mm	UL 746	125	°C
	RTI Imp	RTI Imp	0.75 mm	UL 746	125	°C
RTI Elec	3.0 mm	UL 746	140	°C
	RTI Elec	1.5 mm	UL 746	140	°C
	RTI Elec	RTI Elec	0.75 mm	UL 746	140	°C
Linear coefficient of thermal expansion	Across Flow : 23 to 55°C	ISO 11359-2	1.1E-4	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Flow : 23 to 55°C	ISO 11359-2	2.0E-5	cm/cm/°C
Melting temperature		ISO 11357-3	260	°C
Hot deformation temperature	1.8 MPa, Unannealed	ISO 75-2/A	250	°C
Hot deformation temperature	Hot deformation temperature	0.45 MPa, Unannealed	ISO 75-2/B	260	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	1.6	%
Water absorption rate	Water absorption rate	24 hr, 23°C	ISO 62	0.80	%
Shrinkage rate	Flow : 2.00 mm	ISO 294-4	0.40	%
Shrinkage rate	Shrinkage rate	横向Flow : 2.00 mm	ISO 294-4	0.90	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Volume resistivity	0.750 mm	IEC 60093	1.0E+13	ohms·cm
Dielectric strength	1.00 mm	IEC 60243	20	KV/mm
Arc resistance	3.00 mm	ASTM D495	PLC 6
High arc combustion index	0.75 mm	UL 746	PLC 0
	High arc combustion index	1.5 mm	UL 746	PLC 0
	High arc combustion index	High arc combustion index	3.0 mm	UL 746	PLC 0
High voltage arc tracing rate		UL 746	PLC 1
Hot wire ignition	0.75 mm	UL 746	PLC 4
	Hot wire ignition	1.5 mm	UL 746	PLC 3
	Hot wire ignition	Hot wire ignition	3.0 mm	UL 746	PLC 4

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top