POM Delrin® 500P NC010 DUPONT USA
111
- Properties:High rigidityAging resistancecurrencyWeather resistance
- Usages:Automotive sectorFitness equipment
- Certificates:UL
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Water absorption rate | 饱和,23°C,2.00mm | ISO62 | 1.4 | % |
| 平衡,23°C,2.00mm,50%RH | ISO62 | 0.40 | % | |
| Shrinkage rate | TD | ISO294-4 | 1.9 | % |
| MD | ISO294-4 | 2.0 | % | |
| MediumDensity | 1.19 | g/cm³ | ||
| ThermalConductivityofMelt | 0.24 | W/m/K | ||
| Melt Volume-Flow Rate (MVR) | 190°C/2.16kg | ISO1133 | 13.0 | cm3/10min |
| Melt mass flow rate | ISO1133 | 15 | g/10min | |
| density | ISO1183 | 1.42 | g/cm³ |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Nominal tensile fracture strain | ISO527-2 | 30 | % | |
| Charpy Notched Impact Strength | -30°C | ISO179/1eA | 8.0 | kJ/m² |
| 23°C | ISO179/1eA | 9.0 | kJ/m² | |
| Impact strength of cantilever beam gap | -30°C | ISO180/1A | 8.0 | kJ/m² |
| 23°C | ISO180/1A | 9.0 | kJ/m² | |
| Poisson's ratio | ISO527 | 0.35 | ||
| Multi axis Instrumented Impact Energy | 23°C | ISO6603-2 | 3.00 | J |
| Multi axis Instrumented Peak Impact Force | 23°C | ISO6603-2 | 2000 | N |
| Cantilever beam without notch impact strength | -30°C | ISO180/1U | 250 | kJ/m² |
| 23°C | ISO180/1U | 280 | kJ/m² | |
| TensileCreepModule | 1hr | ISO899-1 | 2800 | Mpa |
| Impact strength of simply supported beam without notch | -30°C | ISO179/1eU | 280 | kJ/m² |
| 23°C | ISO179/1eU | 320 | kJ/m² | |
| Ball pressure hardness | H358/30 | ISO2039-1 | 192 | Mpa |
| Tensile creep modulus | 1000hr | ISO899-1 | 1600 | Mpa |
| Tensile modulus | ISO527-2 | 3100 | Mpa | |
| tensile strength | 屈服 | ISO527-2 | 71.0 | Mpa |
| elongation | 屈服 | ISO527-2 | 17 | % |
| Rockwell hardness | M计秤 | ISO2039-2 | 92 | |
| R计秤 | ISO2039-2 | 120 | ||
| Bending modulus | ISO178 | 3000 | Mpa | |
| bending strength | 3.5%应变 | ISO178 | 80.0 | Mpa |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| vicat softening point | ISO306/B50 | 155 | °C | |
| Melting temperature | ISO11357-3 | 178 | °C | |
| Hot deformation temperature | 0.45MPa,未退火 | ISO75-2/B | 160 | °C |
| 1.8MPa,未退火 | ISO75-2/A | 95.0 | °C | |
| Linear coefficient of thermal expansion | MD：-- | ISO11359-2 | 1E-04 | cm/cm/°C |
| MD：-40to23°C | ISO11359-2 | 9E-05 | cm/cm/°C | |
| TD：-- | ISO11359-2 | 1E-04 | cm/cm/°C | |
| TD：-40to23°C | ISO11359-2 | 9E-05 | cm/cm/°C | |
| TD：AnnealingTemperature | ISO11359-2 | 160 | °C | |
| TD：AnnealingTime-Optional | ISO11359-2 | 30.0 | min/mm | |
| TD：EffectiveThermalDiffusivity | ISO11359-2 | 9E-08 | m²/s | |
| Ball Pressure Test | 165°C | IEC60695-10-2 | Pass |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Relative permittivity | 100Hz | IEC60250 | 3.80 | |
| 1MHz | IEC60250 | 3.80 | ||
| Leakage Trace Index | IEC60112 | 600 | V | |
| Dielectric strength | IEC60243-1 | 44 | KV/mm | |
| Dissipation factor | 100Hz | IEC60250 | 9E-03 | |
| 1MHz | IEC60250 | 5.5E-03 | ||
| Surface resistivity | IEC60093 | 4E+14 | ohms | |
| Volume resistivity | IEC60093 | 2E+14 | ohms·cm |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| FMVSS flammability | FMVSS302 | B | ||
| atomization | F-value(refraction) | ISO6452 | 90 | % |
| G-value(condensate) | ISO6452 | 3.5E-04 | g | |
| Burning rate | 1.00mm | ISO3795 | 20 | mm/min |
| UL flame retardant rating | 0.8mm | IEC60695-11-10,-20 | HB | |
| 1.5mm | IEC60695-11-10,-20 | HB | ||
| 0.8mm | UL94 | HB | ||
| 1.5mm | UL94 | HB | ||
| Extreme Oxygen Index | ISO4589-2 | 22 | % |
| Supplementary Information | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Emission | VDA275 | <8.00 | mg/kg | |
| EmissionofOrganicCompounds | VDA277 | 3.10 | µgC/g |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
You May Like
Contact Us
Get App
Top