PA66 66B ASCEND USA

Form：Granules

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Certificates

No Data...

Technical Data Sheet

impact performance	Test Condition	Test Method	Test Result	Test Unit
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	0.71 mm	UL 94	HB
	UL flame retardant rating	1.5 mm	UL 94	HB
	UL flame retardant rating	UL flame retardant rating	3.0 mm	UL 94	V-2
Burning wire flammability index	0.71 mm	IEC 60695-2-12	850	°C
	Burning wire flammability index	1.5 mm	IEC 60695-2-12	850	°C
	Burning wire flammability index	Burning wire flammability index	3.0 mm	IEC 60695-2-12	960	°C
Hot filament ignition temperature	0.71 mm	IEC 60695-2-13	700	°C
	Hot filament ignition temperature	1.5 mm	IEC 60695-2-13	700	°C
	Hot filament ignition temperature	Hot filament ignition temperature	3.0 mm	IEC 60695-2-13	700	°C
Extreme Oxygen Index		ASTM D2863	28	%
squeeze out	Test Condition	Test Method	Test Result	Test Unit
Temperature in Zone 1 of the material cylinder			250 to 295	°C
Temperature in Zone 2 of the material cylinder			250 to 295	°C
Temperature in Zone 3 of the material cylinder			250 to 295	°C
Temperature in Zone 4 of the material cylinder			250 to 295	°C
Temperature in Zone 5 of the material cylinder			250 to 295	°C
Melt Temperature			270 to 295	°C
Oral mold temperature			270 to 295	°C
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile modulus	23°C	ISO 527-2/1A	2800	Mpa
tensile strength	Yield, 23°C	ISO 527-2/1A	85.0	Mpa
tensile strength	tensile strength	Break, 23°C	ISO 527-2/1A	55.0	Mpa
Tensile strain	Yield, 23°C	ISO 527-2	5.0	%
Nominal tensile fracture strain	23°C	ISO 527-2/1A	> 25	%
Bending modulus	23°C	ISO 178	3100	Mpa
bending strength	23°C	ISO 178	90.0	Mpa
Poisson's ratio	23°C	ISO 527-2	0.42
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45 MPa, Unannealed	ISO 75-2/B	195	°C
Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed	ISO 75-2/A	70.0	°C
Melting temperature		ISO 11357-3	260	°C
Linear coefficient of thermal expansion	Flow : 23 to 55°C, 2.00 mm	ISO 11359-2	1.0E-4	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Across Flow : 23 to 55°C, 2.00 mm	ISO 11359-2	1.0E-4	cm/cm/°C
RTI Elec	0.71 mm	UL 746	130	°C
	RTI Elec	1.5 mm	UL 746	130	°C
	RTI Elec	RTI Elec	3.0 mm	UL 746	130	°C
RTI Imp	0.71 mm	UL 746	75.0	°C
	RTI Imp	1.5 mm	UL 746	75.0	°C
	RTI Imp	RTI Imp	3.0 mm	UL 746	75.0	°C
RTI	0.71 mm	UL 746	85.0	°C
	RTI	1.5 mm	UL 746	85.0	°C
	RTI	RTI	3.0 mm	UL 746	85.0	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Shrinkage rate	横向Flow : 2.00 mm	ISO 294-4	2.0	%
Shrinkage rate	Shrinkage rate	Flow : 2.00 mm	ISO 294-4	2.1	%
Water absorption rate	Saturation, 23°C	ISO 62	8.5	%
Water absorption rate	Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	2.5	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Dielectric strength	1.00 mm	IEC 60243	26	KV/mm
Arc resistance	3.00 mm	ASTM D495	PLC 5
High arc combustion index	0.71 mm	UL 746	PLC 0
	High arc combustion index	1.5 mm	UL 746	PLC 0
	High arc combustion index	High arc combustion index	3.0 mm	UL 746	PLC 0
High voltage arc tracing rate		UL 746	PLC 0
Hot wire ignition	0.71 mm	UL 746	PLC 4
	Hot wire ignition	1.5 mm	UL 746	PLC 3
	Hot wire ignition	Hot wire ignition	3.0 mm	UL 746	PLC 2

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top