Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| density | | ASTM D792 | 0.928 g/cm³ |
| density | | ISO 1183 | 0.930 g/cm³ |
| viscosity number | | ISO 307 | 2300 cm³/g |
| ElongationalStressF | | ISO 1152-2 | 0.240 MPa |
| intrinsic viscosity | | ISO 1628-3 | 20 dl/g |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Shore hardness | | ISO 868 | 60 |
| ball-indentation hardness | | ISO 2039-1 | 36.0 MPa |
| Shore hardness | | ASTM D2240 | 63 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | HB |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| coefficient of friction | Steel - Dynamic | 内部方法 | 0.10 |
| Wear factor | | 内部方法 | 100 |
| Wear amount | | 内部方法 | 100 |
| Tensile modulus | | ASTM D638 | 703 MPa |
| Tensile modulus | | ISO 527-2/1A/1 | 680 MPa |
| tensile strength | | ASTM D638 | 21.4 MPa |
| tensile strength | Yield | ISO 527-2/1A/50 | 20.0 MPa |
| Tensile strain | Yield | ISO 527-2/1A/50 | 13 % |
| Nominal tensile fracture strain | | ISO 527-2/1A/50 | >50 % |
| Tensile creep modulus | | ISO 899-1 | 460 MPa |
| Tensile creep modulus | | ISO 899-1 | 230 MPa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Charpy Notched Impact Strength | | ISO 179/1eA | 无断裂 |
| Charpy Notched Impact Strength | | ISO 179/1eA | 无断裂 |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 无断裂 |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 无断裂 |
| Charpy Notched Impact Strength | | ISO 1152-2 | 240 kJ/m² |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| dielectric constant | | IEC 60250 | 2.00 |
| dielectric constant | | IEC 60250 | 2.00 |
| Dissipation Factor | | IEC 60250 | 3.9E-04 |
| Dissipation Factor | | IEC 60250 | 1E-03 |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | PLC 0 |
| Surface Resistivity | | ASTM D257 | >1.0E+13 ohms |
| Surface Resistivity | | IEC 60093 | >1.0E+12 ohms |
| Volume resistivity | | ASTM D257 | >1.0E+15 ohms·cm |
| Volume resistivity | | IEC 60093 | >1.0E+14 ohms·cm |
| dielectric strength | | IEC 60243-1 | 45 kV/mm |
| dielectric constant | | ASTM D150 | 3.00 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ISO 75-2/B | 65.0 °C |
| Heat distortion temperature | | ISO 75-2/A | 38.0 °C |
| vicat | | ASTMD1525 | 80.0 °C |
| Linear coefficient of thermal expansion | | ASTMD696 | 2E-04 cm/cm/°C |
| specific heat | | 内部方法 | 1840 J/kg/°C |
| thermal conductivity | | 内部方法 | 0.41 W/m/K |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare