PEEK 450G903 VICTREX UK

Form：Granules

Properties:

High rigidityhigh strengthChemical resistanceSemi crystallineGood disinfection performModerate liquidityFood contact complianceDuctility

Typical Applications:

Non specific foodMedical suppliesNursing supplies

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Typical Applications:	Non specific food \| Medical supplies \| Nursing supplies
Properties:	High rigidity \| high strength \| Chemical resistance \| Semi crystalline \| Good disinfection perform \| Moderate liquidity \| Food contact compliance \| Ductility

Certificates

No Data...

Technical Data Sheet

Filling analysis	Test Condition	Test Method	Test Result	Test Unit
Melt viscosity	400°C	ISO 11443	350	Pa·s
impact performance	Test Condition	Test Method	Test Result	Test Unit
Suspended wall beam without notch impact strength	23°C	ISO 180	无断裂
flammability	Test Condition	Test Method	Test Result	Test Unit
Burning wire flammability index	2.0mm	IEC 60695-2-12	960	°C
Extreme Oxygen Index	--12	ISO 4589-2	24	%
Extreme Oxygen Index	Extreme Oxygen Index	--13	ISO 4589-2	35	%
toxicity	COcontent	NES713	0.0740
	toxicity	CO2content	NES713	0.150
	toxicity	toxicity	Totalgases	NES713	0.220
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Bending modulus	23°C	ISO 178	3800	Mpa
bending strength	23°C7	ISO 178	165	Mpa
	bending strength	3.5%Strain,23°C	ISO 178	125	Mpa
		bending strength	125°C	ISO 178	85.0	Mpa
			bending strength	175°C	ISO 178	19.0	Mpa
			bending strength	bending strength	275°C	ISO 178	12.5	Mpa
Compressive stress	23°C	ISO 604	125	Mpa
Compressive stress	Compressive stress	120°C	ISO 604	70.0	Mpa
Tensile modulus	23°C	ISO 527-2	3900	Mpa
tensile strength	Yield,23°C	ISO 527-2	98.0	Mpa
Tensile strain	Break,23°C	ISO 527-2	30	%
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	1.8MPa,Unannealed	ISO 75-2/Af	152	°C
Glass transition temperature	--8	ISO 11357-2	143	°C
Glass transition temperature	Glass transition temperature	--9	ISO 11357-2	150	°C
Melting temperature		ISO 11357-3	343	°C
Linear coefficient of thermal expansion	MD:<143°C	ISO 11359-2	4.5E-05	cm/cm/°C
	Linear coefficient of thermal expansion	MD:>143°C	ISO 11359-2	1.2E-04	cm/cm/°C
		Linear coefficient of thermal expansion	TD:<143°C	ISO 11359-2	5.5E-05	cm/cm/°C
		Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	TD:>143°C	ISO 11359-2	1.4E-04	cm/cm/°C
thermal conductivity	23°C10	ISO 22007-4	0.29	W/m/K
thermal conductivity	thermal conductivity	23°C11	ISO 22007-4	0.32	W/m/K
RTI Elec		UL 746	260	°C
RTI Imp		UL 746	180	°C
RTI		UL 746	240	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Spiral flow length		Internal Method	11.0	CM
Shrinkage rate	TD	ISO 294-4	1.3	%
Shrinkage rate	Shrinkage rate	MD	ISO 294-4	1.0	%
Water absorption rate	Saturation,23°C	ISO 62	0.45	%
Water absorption rate	Water absorption rate	100°C，Saturation	ISO 62	0.55	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Volume resistivity	23°C	IEC 60093	1E+16	ohms·cm
	Volume resistivity	125°C	IEC 60093	1E+15	ohms·cm
	Volume resistivity	Volume resistivity	275°C	IEC 60093	1E+09	ohms·cm
Dielectric strength	2.00mm	IEC 60243-1	24	KV/mm
Dielectric constant	23°C,1kHz	IEC 60250	2.90
Dissipation factor	23°C,1MHz	IEC 60250	4E-03
Compared to the anti leakage trace index		IEC 60112	PLC 4
hardness	Test Condition	Test Method	Test Result	Test Unit
Shore hardness	ShoreD,23°C	ISO 868	85

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top