
PBT 5010R8 MITSUBISHI ENGINEERING JAPAN
96
Form:Granules | Grade:Impact resistant grade
Properties:
Glass fiber reinforcedFlame retardant
Typical Applications:
Bottle capVehicle electronics
Product Description
Certificates(0)
Datasheet
Product Description
| Typical Applications: | Bottle cap | Vehicle electronics |
| Properties: | Glass fiber reinforced | Flame retardant |
Certificates
No Data...
Technical Data Sheet
| impact performance | Test Condition | Test Method | Test Result | Test Unit |
|---|---|---|---|---|
| Impact strength of simply supported beam without notch | 23°C | ISO 179 | >200 | kJ/m² |
| flammability | Test Condition | Test Method | Test Result | Test Unit |
| UL flame retardant rating | 0.8mm | UL 94 | HB | |
| mechanical properties | Test Condition | Test Method | Test Result | Test Unit |
| bending strength | ISO 178 | 56.0 | Mpa | |
| Nominal tensile fracture strain | ISO 527-2 | >200 | % | |
| Tensile strain | Yield | ISO 527-2 | 11 | % |
| tensile strength | Yield | ISO 527-2 | 45.0 | Mpa |
| Bending modulus | ISO 178 | 1650 | Mpa | |
| Tensile modulus | ISO 527-2 | 1550 | Mpa | |
| thermal performance | Test Condition | Test Method | Test Result | Test Unit |
| Linear coefficient of thermal expansion | TD:-30to50°C | ISO 11359-2 | 1.1E-04 | cm/cm/°C |
| TD:50to120°C | ISO 11359-2 | 1.6E-04 | cm/cm/°C | |
| MD:50to120°C | ISO 11359-2 | 1.7E-04 | cm/cm/°C | |
| Hot deformation temperature | 0.45MPa,Unannealed | ISO 75-2/B | 155 | °C |
| Linear coefficient of thermal expansion | MD:-30to50°C | ISO 11359-2 | 1.1E-04 | cm/cm/°C |
| TD:-30to120°C | ISO 11359-2 | 1.4E-04 | cm/cm/°C | |
| Hot deformation temperature | 1.8MPa,Unannealed | ISO 75-2/A | 70.0 | °C |
| Melting temperature | ISO 11357-3 | 222 | °C | |
| Linear coefficient of thermal expansion | MD:-30to120°C | ISO 11359-2 | 1.4E-04 | cm/cm/°C |
| Physical properties | Test Condition | Test Method | Test Result | Test Unit |
| Shrinkage rate | 吸水率(Saturation,23°C) | 0.090 | % | |
| MD:2.00mm | 2.0 | % | ||
| TD:2.00mm | 1.9 | % | ||
| Electrical performance | Test Condition | Test Method | Test Result | Test Unit |
| Dissipation factor | 1MHz | IEC 60250 | 0.025 | |
| Relative permittivity | 1MHz | IEC 60250 | 3.40 | |
| Dielectric strength | 2.00mm | IEC 60243-1 | 17 | KV/mm |
| 1.00mm | IEC 60243-1 | 23 | KV/mm | |
| Surface resistivity | IEC 60093 | 4E+15 | ohms | |
| Volume resistivity | IEC 60093 | 1E+16 | ohms·cm | |
| Compared to the anti leakage trace index | CTI | UL 746 | PLC 0 |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.