Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| density | | ISO 1183 | 1.35 g/cm³ |
| Apparent density | | ISO 60 | 0.70 g/cm³ |
| Melt volume flow rate | | ISO 1133 | 14.0 cm³/10min |
| Shrinkage rate | | ISO 2577 | 0.50to0.70 % |
| Shrinkage rate | | ISO 2577 | 0.10to0.20 % |
| Shrinkage rate | | ISO 2577 | 0.50to0.70 % |
| Shrinkage rate | | ISO 2577 | 0.10to0.20 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| ball-indentation hardness | | ISO 2039-1 | 95.0 MPa |
| flammability | Test Condition | Test Method | Test Result |
|---|
| Burning rate - US-FMVSS | | ISO 3795 | passed |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| electrolytic corrosion | | IEC 60426 | A1 |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile strain | | ISO 527-2/5 | 3.0 % |
| Tensile modulus | | ISO 527-2/1 | 4200 MPa |
| tensile strength | | ISO 527-2/5 | 50.0 MPa |
| tensile strength | | ISO 527-2/5 | 50.0 MPa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of cantilever beam gap | | ISO 180/A | 9.0 kJ/m² |
| Suspended wall beam without notch impact strength | | ISO 180 | 60 kJ/m² |
| Suspended wall beam without notch impact strength | | ISO 180 | 85 kJ/m² |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| relative permittivity | | IEC 60250 | 3.50 |
| Dissipation Factor | | IEC 60250 | 5E-03 |
| Dissipation Factor | | IEC 60250 | 0.020 |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | PLC 2 |
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | PLC 4 |
| Surface Resistivity | | IEC 60093 | >1.0E+17 ohms |
| Volume resistivity | | IEC 60093 | >1.0E+17 ohms·cm |
| dielectric strength | | IEC 60243-1 | 40 kV/mm |
| relative permittivity | | IEC 60250 | 3.70 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ISO 75-2/A | 112 °C |
| vicat | | ISO 306/B120 | 135 °C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 5E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 5E-05 cm/cm/°C |
| Heat distortion temperature | | ISO 75-2/B | 130 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare