PPO V0150B-701 SABIC INNOVATIVE SHANGHAI

Form：Granules | Grade：Injection grade

Properties:

High temperature resistanHigh mobilityGlass fiber reinforced

Typical Applications:

Automotive interior partsElectrical applications

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Typical Applications:	Automotive interior parts \| Electrical applications
Properties:	High temperature resistan \| High mobility \| Glass fiber reinforced

Certificates

No Data...

Technical Data Sheet

impact performance	Test Condition	Test Method	Test Result	Test Unit
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	5.0	kJ/m²
Charpy Notched Impact Strength	Charpy Notched Impact Strength	23°C	ISO 179/1eA	14	kJ/m²
Dart impact	23°C, Total Energy	ASTM D3763	50.0	J
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	1.5 mm	UL 94	V-0
UL flame retardant rating	UL flame retardant rating	2.0 mm	UL 94	5VA
Burning wire flammability index	1.0 mm	IEC 60695-2-12	960	°C
Hot filament ignition temperature	1.0 mm	IEC 60695-2-13	775	°C
	Hot filament ignition temperature	2.0 mm	IEC 60695-2-13	775	°C
	Hot filament ignition temperature	Hot filament ignition temperature	3.0 mm	IEC 60695-2-13	775	°C
Extreme Oxygen Index		ISO 4589-2	32	%
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile modulus	--3	ASTM D638	2500	Mpa
Tensile modulus	Tensile modulus	--	ISO 527-2/1	2500	Mpa
tensile strength	Yield4	ASTM D638	70.0	Mpa
	tensile strength	Yield	ISO 527-2/50	70.0	Mpa
		tensile strength	Break4	ASTM D638	60.0	Mpa
		tensile strength	tensile strength	Break	ISO 527-2/50	55.0	Mpa
elongation	Yield4	ASTM D638	5.0	%
	elongation	Yield	ISO 527-2/50	4.0	%
		elongation	Break4	ASTM D638	7.0	%
		elongation	elongation	Break	ISO 527-2/50	10	%
Bending modulus	50.0 mm Span5	ASTM D790	2550	Mpa
Bending modulus	Bending modulus	--6	ISO 178	2400	Mpa
bending strength	--6,7	ISO 178	110	Mpa
bending strength	bending strength	Yield, 50.0 mm Span5	ASTM D790	105	Mpa
Taber abraser	1000 Cycles, 1000 g, CS-17 Wheel	Internal Method	35.0	mg
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			110 to 120	°C
drying time			2.0 to 3.0	hr
Hopper temperature			80 to 100	°C
Temperature at the rear of the barrel			260 to 280	°C
Temperature in the middle of the barrel			280 to 300	°C
Temperature at the front of the material cylinder			300 to 320	°C
Spray nozzle temperature			280 to 300	°C
Processing (melt) temperature			300 to 320	°C
Mold temperature			100 to 130	°C
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45 MPa, Unannealed, 4.00 mm, 100 mm Span10	ISO 75-2/Be	140	°C
	Hot deformation temperature	1.8 MPa, Unannealed, 3.20 mm	ASTM D648	135	°C
	Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 100 mm Span10	ISO 75-2/Ae	130	°C
Vicat softening temperature	--	ASTM D152511	155	°C
	Vicat softening temperature	--	ISO 306/A50	160	°C
	Vicat softening temperature	Vicat softening temperature	--	ISO 306/B50	145	°C
Ball Pressure Test	123 to 127°C	IEC 60695-10-2	通过
Ball Pressure Test	Ball Pressure Test	140°C12	IEC 60695-10-2	通过
Linear coefficient of thermal expansion	Flow : -40 to 40°C	ASTM E831	7.5E-5	cm/cm/°C
	Linear coefficient of thermal expansion	Flow : 23 to 80°C	ISO 11359-2	7.0E-5	cm/cm/°C
		Linear coefficient of thermal expansion	Across Flow : -40 to 40°C	ASTM E831	7.5E-5	cm/cm/°C
		Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Across Flow : 23 to 80°C	ISO 11359-2	9.0E-5	cm/cm/°C
thermal conductivity		ISO 8302	0.27	W/m/K
RTI Elec		UL 746	110	°C
RTI Imp		UL 746	105	°C
RTI		UL 746	115	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
melt mass-flow rate	280°C/5.0 kg	ASTM D1238	3.5	g/10 min
Melt Volume Flow Rate (MVR)	300°C/5.0 kg	ISO 1133	10.0	cm3/10min
Shrinkage rate	--2，Flow	Internal Method	0.50 - 0.70	%
Shrinkage rate	Shrinkage rate	3.20 mm，Flow	Internal Method	0.50 - 0.70	%
Water absorption rate	Saturation, 23°C	ISO 62	0.18	%
Water absorption rate	Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	0.060	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Surface resistivity		IEC 60093	> 1.0E+15	ohms
Volume resistivity		IEC 60093	1.0E+15	ohms·cm
Dielectric strength	0.800 mm, in Oil	IEC 60243-1	33	KV/mm
	Dielectric strength	1.60 mm, in Oil	IEC 60243-1	26	KV/mm
	Dielectric strength	Dielectric strength	3.20 mm, in Oil	IEC 60243-1	16	KV/mm
Relative permittivity	50 Hz	IEC 60250	2.80
	Relative permittivity	60 Hz	IEC 60250	2.80
	Relative permittivity	Relative permittivity	1 MHz	IEC 60250	2.70
Dissipation factor	50 Hz	IEC 60250	9.0E-4
	Dissipation factor	60 Hz	IEC 60250	9.0E-4
	Dissipation factor	Dissipation factor	1 MHz	IEC 60250	3.0E-3
Compared to the anti leakage trace index		IEC 60112		V
hardness	Test Condition	Test Method	Test Result	Test Unit
Ball Pressure Test	H 358/30	ISO 2039-1	113	Mpa

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top