Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Water absorption rate | | ISO 62 | 1.1 % |
| Water absorption rate | | ISO 62 | 3.1 % |
| Outdoor applicability | | UL 746C | f1 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | V-0 |
| Burning wire flammability index | | IEC 60695-2-12 | 960 °C |
| Burning wire flammability index | | IEC 60695-2-12 | 960 °C |
| Burning wire flammability index | | IEC 60695-2-12 | 960 °C |
| GWIT | | IEC 60695-2-13 | 650 °C |
| Limiting Oxygen Index | | ISO 4589-2 | 33 % |
| UL flame retardant rating | | NFF16-101 | F2 |
| smoke density | | NFF16-101 | I2 |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| EuropeanRailwaysCertifications | | EN45545-2 | HL2 |
| EuropeanRailwaysCertifications | | EN45545-2 | HL3 |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ISO 527-2/1A | 3750 Mpa |
| tensile strength | | ASTM D638 | 85.0 Mpa |
| tensile strength | | ISO 527-2/1A | 80.0 Mpa |
| tensile strength | | ISO 527-2/1A | 70.0 Mpa |
| Tensile strain | | ISO 527-2 | 4.0 % |
| elongation | | ASTM D638 | 15 % |
| Tensile strain | | ISO 527-2 | 12 % |
| Flexural modulus | | ASTM D790 | 3800 Mpa |
| Flexural modulus | | ISO 178 | 3700 Mpa |
| bending strength | | ASTM D790 | 125 Mpa |
| bending strength | | ISO 178 | 130 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 80 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | 70 kJ/m² |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Compared to the Leakage Tracking Index (CTI) | | IEC 60112 | PLC 0 |
| Surface Resistivity | | IEC 60093 | 1E+15 ohms |
| Volume resistivity | | IEC 60093 | 1E+15 ohms·cm |
| dielectric strength | | IEC 60243-1 | 33 KV/mm |
| relative permittivity | | IEC 60250 | 3.60 |
| Dissipation Factor | | IEC 60250 | 0.020 |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 85.0 °C |
| Heat distortion temperature | | ISO 75-2/Af | 85.0 °C |
| melting temperature | | ISO 11357-3 | 242 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare