PPA HTNFR52G45BL BK337 DUPONT USA

Form：Granules | Grade：Flame retardant enhanced grade

Properties:

Dimensional stabilityLow water absorptionHeat aginghigh strengthHigh rigidity

Typical Applications:

household electrical appliancesAutomotive interior partselectrical equipment

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Typical Applications:	household electrical appliances \| Automotive interior parts \| electrical equipment
Properties:	Dimensional stability \| Low water absorption \| Heat aging \| high strength \| High rigidity

Certificates

No Data...

Technical Data Sheet

impact performance	Test Condition	Test Method	Test Result	Test Unit
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	45	kJ/m²
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	48	kJ/m²
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating		UL 94	V-0
Burning wire flammability index	0.40 mm	IEC 60695-2-12	960	°C
	Burning wire flammability index	0.75 mm	IEC 60695-2-12	960	°C
		Burning wire flammability index	1.5 mm	IEC 60695-2-12	960	°C
		Burning wire flammability index	Burning wire flammability index	3.0 mm	IEC 60695-2-12	960	°C
Hot filament ignition temperature	0.40 mm	IEC 60695-2-13	700	°C
	Hot filament ignition temperature	0.75 mm	IEC 60695-2-13	750	°C
		Hot filament ignition temperature	1.5 mm	IEC 60695-2-13	750	°C
		Hot filament ignition temperature	Hot filament ignition temperature	3.0 mm	IEC 60695-2-13	800	°C
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile modulus		ISO 527-2	15500	Mpa
tensile strength	Break	ISO 527-2	167	Mpa
Tensile strain	Break	ISO 527-2	1.7	%
Bending modulus		ISO 178	15100	Mpa
bending strength		ISO 178	249	Mpa
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			100	°C
Drying time - hot air dryer			6.0 to 8.0	hr
Suggested maximum moisture content			0.10	%
Processing (melt) temperature			320 to 325	°C
Mold temperature			90 to 130	°C
Mold temperature	Mold temperature	Drying Recommended		yes
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	1.8 MPa, Unannealed	ISO 75-2/A	284	°C
Melting temperature		ISO 11357-3	310	°C
Linear coefficient of thermal expansion	Flow	ISO 11359-2	1.5E-5	cm/cm/°C
	Linear coefficient of thermal expansion	Flow : -40 to 23°C	ISO 11359-2	1.3E-5	cm/cm/°C
		Linear coefficient of thermal expansion	Flow : 55 to 160°C	ISO 11359-2	1.4E-5	cm/cm/°C
			Linear coefficient of thermal expansion	Across Flow	ISO 11359-2	5.0E-5	cm/cm/°C
				Linear coefficient of thermal expansion	Across Flow : -40 to 23°C	ISO 11359-2	4.3E-5	cm/cm/°C
				Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	Across Flow : 55 to 160°C	ISO 11359-2	8.0E-5	cm/cm/°C
RTI Elec	0.40 mm	UL 746	140	°C
	RTI Elec	0.75 mm	UL 746	140	°C
		RTI Elec	1.5 mm	UL 746	140	°C
		RTI Elec	RTI Elec	3.0 mm	UL 746	140	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Shrinkage rate	横向Flow	ISO 294-4	0.60	%
Shrinkage rate	Shrinkage rate	Flow	ISO 294-4	0.20	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Volume resistivity		IEC 62631-3-1	> 1.0E+13	ohms·m
Dielectric strength		IEC 60243-1	40	KV/mm
Relative permittivity	1 MHz	IEC 62631-2-1	4.40
Relative permittivity	Relative permittivity	100 Hz	IEC 62631-2-1	4.70
Dissipation factor	100 Hz	IEC 62631-2-1	6.0E-3
Dissipation factor	Dissipation factor	1 MHz	IEC 62631-2-1	0.012
Compared to the anti leakage trace index		IEC 60112	PLC 0

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top