Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTM D1238 | 18 g/10min |
| Melt volume flow rate | | ISO 1133 | 16.0 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.50-0.70 % |
| Water absorption rate | | ISO 62 | 0.35 % |
| Water absorption rate | | ISO 62 | 0.15 % |
| Outdoor applicability | | UL 746C | f2 |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| refractive index | | ISO 489 | 1.590 |
| transmissivity | | ASTM D1003 | 89.0 % |
| Haze ratio | | ASTM D1003 | 0.60 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-2 |
| Burning wire flammability index | | IEC 60695-2-12 | 960 °C |
| Hot filament ignition temperature | | IEC 60695-2-13 | 825 °C |
| Hot filament ignition temperature | | IEC 60695-2-13 | 825 °C |
| Hot filament ignition temperature | | IEC 60695-2-13 | 825 °C |
| Hot filament ignition temperature | | IEC 60695-2-13 | 825 °C |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| tensile strength | | ASTM D638 | 65.0 Mpa |
| tensile strength | | ISO 527-2/50 | 67.0 Mpa |
| tensile strength | | ASTM D638 | 67.0 Mpa |
| tensile strength | | ISO 527-2/50 | 70.0 Mpa |
| elongation | | ASTM D638 | 6.0 % |
| Tensile strain | | ISO 527-2/50 | 6.0 % |
| elongation | | ASTM D638 | >100 % |
| Tensile strain | | ISO 527-2/50 | >100 % |
| Flexural modulus | | ASTM D790 | 2450 Mpa |
| Flexural modulus | | ISO 178 | 2450 Mpa |
| Tensile modulus | | ASTM D638 | 2400 Mpa |
| Tensile modulus | | ISO 527-2/1 | 2300 Mpa |
| bending strength | | ISO 178 | 96.0 Mpa |
| bending strength | | ASTM D790 | 96.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Dart impact | | ASTM D3763 | 80.0 J |
| Charpy Notched Impact Strength | | ISO 179/1eA | 15 kJ/m² |
| Charpy Notched Impact Strength | | ISO 179/1eA | 65 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO 179/1eU | NoBreak |
| Impact strength of cantilever beam gap | | ISO 180/1A | 10 kJ/m² |
| Impact strength of cantilever beam gap | | ISO 180/1A | 65 kJ/m² |
| Suspended wall beam without notch impact strength | | ISO 180/1U | NoBreak |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 124 °C |
| Heat distortion temperature | | ISO 75-2/Af | 124 °C |
| vicat | | ASTM D152510 | 139 °C |
| vicat | | ISO 306/B50 | 139 °C |
| vicat | | ISO 306/B120 | 140 °C |
| ball-indentation hardness | | IEC 60695-10-2 | Pass |
| Linear coefficient of thermal expansion | | ASTME831 | 7E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 7E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ASTME831 | 7E-05 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 7E-05 cm/cm/°C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices