TP, Unspecified MEGOLON™ S300
0
CompareTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|---|---|---|
| density | ASTM D792 | 1.55 g/cm³ | |
| melt mass-flow rate | ISO 1133 | 4.5 g/10min | |
| Mooney viscosity | ASTM D1646 | 45 MU |
| hardness | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Shore hardness | ASTM D2240 | 58 |
| flammability | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Limiting Oxygen Index | ISO 4589-2 | 35 % | |
| Acid gas release | IEC 60754-2 | 14.0 µS/cm | |
| IEC 60754-2 | 5.50 | ||
| Combustion temperature index | ISO 4589-3 | 270 °C | |
| Smoke density | ASTME662 | <130 Ds | |
| ASTME662 | <200 Ds | ||
| toxicity | NES713 | 2.00 |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|---|---|---|
| HalogenAcidGasEvolution | IEC 60754-1 | 0.0 % | |
| ozone resistance | ASTM D470 | pass |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|---|---|---|
| tensile strength | IEC 60811-1-2 | 19.0 MPa | |
| IEC 60811-1-1 | 15.0 MPa | ||
| Tensile strain | IEC 60811-1-2 | 110 % | |
| Break | IEC 60811-1-1 | 150 % | |
| elongation at break | 230 % | ||
| 170 % | |||
| 170 % | |||
| tensile strength | 12.0 MPa | ||
| 14.0 MPa | |||
| 13.0 MPa |
| elastomer | Test Condition | Test Method | Test Result |
|---|---|---|---|
| tear strength | BS646999.1 | 5.00 kN/m |
| aging | Test Condition | Test Method | Test Result |
|---|---|---|---|
| Tensile stress change rate | 13 % | ||
| 50 % | |||
| BS646999.1 | -15 % | ||
| Change rate of tensile strength in air | 26 % | ||
| Change rate of ultimate elongation in air | -25 % | ||
| Change rate of tensile strength in air | -7.0 % | ||
| -11 % | |||
| -22 % | |||
| BS646999.1 | 0.0 % | ||
| Tensile stress change rate | 11 % | ||
| volume change | 1.0 % | ||
| 10 % | |||
| 3.0 % |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| insulation resistance | BS646999.2 | 5E+13 ohms·cm | |
| dielectric constant | ASTM D150 | 4.80 | |
| Dissipation Factor | ASTM D150 | 0.020 | |
| insulation resistance | BS646999.2 | 1E+14 ohms·cm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|---|---|---|
| ColdImpact | IEC 60811-1-4 | pass | |
| Heat distortion temperature | BS646999.1 | 7.0 % | |
| Hot pressing test | IEC 60811-3-1 | 14 % | |
| ColdElongation | IEC 60811-1-4 | 40 % |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Contact Us
Get App
Top