Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTM D1238 | 6.8 g/10 min |
| melt mass-flow rate | | ISO 1133 | 9.0 g/10 min |
| Molten Volume Flow Rate (MVR) | | ISO 1133 | 37.0 cm3/10min |
| Shrinkage rate - flow | | 内部方法 | 0.50 到 0.70 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-0 |
| UL flame retardant rating | | UL 94 | 5VB |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus 2 | | ASTM D638 | 2410 Mpa |
| Tensile strength 3 | | ASTM D638 | 42.0 Mpa |
| Tensile strength 3 | | ASTM D638 | 35.0 Mpa |
| Elongation rate 3 | | ASTM D638 | 2.1 % |
| Elongation rate 3 | | ASTM D638 | 11 % |
| Flexural modulus | | ASTM D790 | 2720 Mpa |
| bending strength | | ASTM D790 | 73.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Dart impact equipped with measuring instruments | | ASTM D3763 | 41.0 J |
| Filling analysis | Test Condition | Test Method | Test Result |
|---|
| melt viscosity | | ASTM D3835 | 310 Pa·s |
| injection | Test Condition | Test Method | Test Result |
|---|
| drying temperature | | | 80 到 90 °C |
| drying time | | | 2.0 到 4.0 hr |
| Suggested maximum moisture content | | | 0.10 % |
| Suggested injection volume | | | 50 到 70 % |
| Temperature at the rear of the barrel | | | 170 到 180 °C |
| Temperature in the middle of the barrel | | | 195 到 205 °C |
| Temperature at the front of the material cylinder | | | 200 到 215 °C |
| Spray nozzle temperature | | | 200 到 220 °C |
| Processing (melt) temperature | | | 200 到 220 °C |
| Temperature | | | 50 到 70 °C |
| Back pressure | | | 0.300 到 0.700 Mpa |
| screw speed | | | 30 到 60 rpm |
| Exhaust hole depth | | | 0.038 到 0.051 mm |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Thermal deformation temperature under load | | ASTM D648 | 83.0 °C |
| Thermal deformation temperature under load | | ASTM D648 | 72.0 °C |
| vicat | | ASTM D15255 | 90.0 °C |
| | ASTM E831 | 7.9E-5 cm/cm/°C |
| | ASTM E831 | 7.9E-5 cm/cm/°C |
| RTI Elec | | UL 746 | 60.0 °C |
| RTI Imp | | UL 746 | 60.0 °C |
| RTI | | UL 746 | 60.0 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare