PC LUX 2180T SABIC INNOVATIVE NANSHA

Form：Granules | Grade：Transparent level

Properties:

OpticsUV resistanceAging resistanceWeather resistanceHigh impact resistance

Typical Applications:

Lighting applications

Supplier(1)

Product Description

Certificates(0)

Datasheet

Product Description

Typical Applications:	Lighting applications
Properties:	Optics \| UV resistance \| Aging resistance \| Weather resistance \| High impact resistance

Certificates

No Data...

Technical Data Sheet

optical performance	Test Condition	Test Method	Test Result	Test Unit
Refractive index		ISO 489	1.586
Transmittance rate	2540μm	ASTM D1003	>90.0	%
	Transmittance rate	2540μm,420nm	Internal Method	>88.0	%
	Transmittance rate	Transmittance rate	5000μm	Internal Method	>89.0	%
turbidity	2540μm	ASTM D1003	<0.50	%
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	0.800mm	UL 94	V-2
Burning wire flammability index	1.00mm	IEC 60695-2-12	850	°C
Hot filament ignition temperature	1.00mm	IEC 60695-2-13	>875	°C
Extreme Oxygen Index		ISO 4589-2	25	%
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂
Impact strength of cantilever beam gap	-30°C	ISO 180/1A	15	kJ/m²
Impact strength of cantilever beam gap	Impact strength of cantilever beam gap	23°C	ISO 180/1A	65	kJ/m²
Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	无断裂
Suspended wall beam without notch impact strength	Suspended wall beam without notch impact strength	23°C	ISO 180/1U	无断裂
tensile strength	Yield	ISO 527-2/50	62.0	Mpa
tensile strength	tensile strength	Break	ISO 527-2/50	69.0	Mpa
Tensile strain	Yield	ISO 527-2/50	6.0	%
Tensile strain	Tensile strain	Break	ISO 527-2/50	100	%
Bending modulus		ISO 178	2300	Mpa
bending strength		ISO 178	90.0	Mpa
Taber abraser	1000Cycles,1000g,CS-17Wheel	Internal Method	10.0	mg
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	12	kJ/m²
Charpy Notched Impact Strength	Charpy Notched Impact Strength	23°C	ISO 179/1eA	65	kJ/m²
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Ball Pressure Test	H358/30	ISO 2039-1	95.0	Mpa
Tensile modulus		ISO 527-2/1	2350	Mpa
thermal performance	Test Condition	Test Method	Test Result	Test Unit
0.45MPa, unannealed, 100mm span		ISO 75-2/Be	133	°C
1.8MPa, unannealed, 100mm span		ISO 75-2/Ae	122	°C
--		ISO 306/B50	140	°C
--	--		ISO 306/B120	141	°C
Ball Pressure Test	125°C	IEC 60695-10-2	Pass
Linear coefficient of thermal expansion	MD：23to80°C	ISO 11359-2	7E-05	cm/cm/°C
thermal conductivity		ISO 8302	0.20	W/m/K
RTI Elec		UL 746	130	°C
RTI Imp		UL 746	125	°C
RTI		UL 746	125	°C
Physical properties	Test Condition	Test Method	Test Result	Test Unit
Melt Volume Flow Rate (MVR)	300°C/1.2kg	ISO 1133	18.0	cm3/10min
Shrinkage rate	MD1	Internal Method	0.50-0.70	%
Water absorption rate	Saturation,23°C	ISO 62	0.35	%
Water absorption rate	Water absorption rate	Equilibrium,23°C,50%RH	ISO 62	0.15	%
Outdoor applicability		UL 746C	f1
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Relative permittivity	1MHz	IEC 60250	2.70
Dissipation factor	50Hz	IEC 60250	1E-03
	Dissipation factor	60Hz	IEC 60250	1E-03
	Dissipation factor	Dissipation factor	1MHz	IEC 60250	0.010
Surface resistivity		IEC 60093	>1.0E+15	ohms
Volume resistivity		IEC 60093	>1.0E+15	ohms·cm
Dielectric strength	3.20mm,in Oil	IEC 60243-1	17	KV/mm
Relative permittivity	50Hz	IEC 60250	2.70
Relative permittivity	Relative permittivity	60Hz	IEC 60250	2.70

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top