Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| Water absorption rate | | ISO62 | 0.10 % |
| melt mass-flow rate | | ISO1133 | 7.0 g/10min |
| Shrinkage rate | | ISO294-4 | 0.45 % |
| Melt volume flow rate | | ISO1133 | 6.00 cm3/10min |
| Shrinkage rate | | ISO294-4 | 0.45 % |
| Water absorption rate | | ISO62 | 0.24 % |
| Apparent density | | ISO60 | 0.64 g/cm³ |
| hardness | Test Condition | Test Method | Test Result |
|---|
| | ISO2039-1 | 129 Mpa |
| other | Test Condition | Test Method | Test Result |
|---|
| | | 防火 |
| purpose | | | IT办公 |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL94 | V-0 |
| needle flame test | | IEC60695-11-5 | 2.0 min |
| needle flame test | | IEC60695-11-5 | 1.0 min |
| SelfIgnitionTemperature | | ASTMD1929 | 550 °C |
| Burning wire flammability index | | IEC60695-2-12 | 960 °C |
| needle flame test | | IEC60695-11-5 | 2.0 min |
| Burning wire flammability index | | IEC60695-2-12 | 850 °C |
| UL flame retardant rating | | UL94 | V-2 |
| Hot filament ignition temperature | | IEC60695-2-13 | 900 °C |
| | ISO3795 | passed |
| needle flame test | | IEC60695-11-5 | 1.0 min |
| Hot filament ignition temperature | | IEC60695-2-13 | 850 °C |
| Hot filament ignition temperature | | IEC60695-2-13 | 900 °C |
| needle flame test | | IEC60695-11-5 | 2.0 min |
| needle flame test | | IEC60695-11-5 | 2.0 min |
| Burning wire flammability index | | IEC60695-2-12 | 960 °C |
| FlashIgnitionTemperature | | ASTMD1929 | 470 °C |
| Extreme Oxygen Index 8 | | ISO4589-2 | 27 % |
| Supplementary Information | Test Condition | Test Method | Test Result |
|---|
| ElectrolyticalCorrosion | | IEC60426 | A1 |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Multi axis Instrumented Impact Energy | | ISO6603-2 | 13.0 J |
| CharpyNotchedImpactStrength6 | | ISO7391 | 10 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO179/1eU | 100 kJ/m² |
| Impact strength of simply supported beam without notch | | ISO179/1eU | 120 kJ/m² |
| Multi axis Instrumented Impact Energy | | ISO6603-2 | 25.0 J |
| NotchedIzodImpactStrength7 | | ISO7391 | 10 kJ/m² |
| Multi axis Instrumented Peak Impact Force | | ISO6603-2 | 3600 N |
| Impact strength of simply supported beam without notch | | ISO179/1eU | 90 kJ/m² |
| Multi axis Instrumented Peak Impact Force | | ISO6603-2 | 3000 N |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile strain | | ISO527-2/5 | 12 % |
| Tensile modulus | | ISO527-2/1 | 4600 Mpa |
| | ISO178 | 5.8 % |
| Tensile strain | | ISO527-2/5 | 4.6 % |
| Tensile stress | | ISO527-2/5 | 45.0 Mpa |
| Tensile stress | | ISO527-2/5 | 64.0 Mpa |
| Bending stress | | ISO178 | 95.0 Mpa |
| Flexural modulus | | ISO178 | 4400 Mpa |
| Bending stress | | ISO178 | 105 Mpa |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Dissipation Factor | | IEC60250 | 9E-03 |
| | IEC60250 | 3.20 |
| Dissipation Factor | | IEC60250 | 1E-03 |
| CTI | | IEC60112 | 125 V |
| | IEC60250 | 3.20 |
| Surface Resistivity | | IEC60093 | 1E+16 ohms |
| dielectric strength | | IEC60243-1 | 38 KV/mm |
| Volume resistivity | | IEC60093 | 1E+16 ohms·cm |
| CTI | | IEC60112 | 175 V |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| | ISO75-2/B | 141 °C |
| | ISO75-2/A | 135 °C |
| RTI Elec | | UL746 | 80.0 °C |
| | ISO11359-2 | 3.5E-05 cm/cm/°C |
| vicat | | ISO306/B120 | 145 °C |
| BallPressure Test | | IEC60695-10-2 | Pass |
| | ISO11359-2 | 6.5E-05 cm/cm/°C |
| RTI Imp | | UL746 | 80.0 °C |
| RTI Str | | UL746 | 80.0 °C |
| vicat | | ISO306/B50 | 142 °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices