Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result |
|---|
| melt mass-flow rate | | ASTM D1238 | 22 g/10 min |
| Melt volume flow rate | | ISO 1133 | 21.0 cm3/10min |
| Shrinkage rate | | 内部方法 | 0.50 - 0.70 % |
| Shrinkage rate | | 内部方法 | 0.50 - 0.70 % |
| Water absorption rate | | ISO 62 | 0.35 % |
| Water absorption rate | | ASTM D570 | 0.35 % |
| hardness | Test Condition | Test Method | Test Result |
|---|
| Rockwell hardness | | ASTM D785 | 120 |
| Rockwell hardness | | ISO 2039-2 | 120 |
| optical performance | Test Condition | Test Method | Test Result |
|---|
| refractive index | | ISO 179/leA | 1.586 |
| transmissivity | | ASTM D1003 | 88.0 to 90.0 % |
| Haze ratio | | ASTM D1003 | < 0.80 % |
| flammability | Test Condition | Test Method | Test Result |
|---|
| UL flame retardant rating | | UL 94 | V-2 |
| Mechanical properties | Test Condition | Test Method | Test Result |
|---|
| Tensile modulus | | ASTM D638 | 2350 Mpa |
| Tensile modulus | | ISO 527-2/1 | 2350 Mpa |
| tensile strength | | ASTM D638 | 63.0 Mpa |
| tensile strength | | ISO 527-2/50 | 63.0 Mpa |
| elongation | | ASTM D638 | 6.0 % |
| elongation | | ISO 527-2/50 | 6.0 % |
| elongation | | ASTM D638 | > 70 % |
| elongation | | ISO 527-2/50 | > 70 % |
| Flexural modulus | | ASTM D790 | 2300 Mpa |
| Flexural modulus | | ISO 178 | 2300 Mpa |
| bending strength | | ISO 178 | 90.0 Mpa |
| bending strength | | ASTM D790 | 90.0 Mpa |
| Impact resistance | Test Condition | Test Method | Test Result |
|---|
| Suspended wall beam without notch impact strength | | ASTM D4812 | 无断裂 |
| Suspended wall beam without notch impact strength | | ISO 180/1U | 无断裂 |
| Dart impact | | ASTM D3763 | 55.0 J |
| Electrical performance | Test Condition | Test Method | Test Result |
|---|
| Volume resistivity | | ASTM D257 | > 1.0E+15 ohms·cm |
| dielectric strength | | ASTM D149 | 27 KV/mm |
| dielectric constant | | ASTM D150 | 3.00 |
| dielectric constant | | ASTM D150 | 3.00 |
| Dissipation Factor | | ASTM D150 | 1.0E-3 |
| Dissipation Factor | | ASTM D150 | 0.010 |
| injection | Test Condition | Test Method | Test Result |
|---|
| drying temperature | | | 120 °C |
| drying time | | | 2.0 to 4.0 hr |
| Suggested maximum moisture content | | | 0.020 % |
| Hopper temperature | | | 60 to 80 °C |
| Temperature at the rear of the barrel | | | 260 to 280 °C |
| Temperature in the middle of the barrel | | | 270 to 290 °C |
| Temperature at the front of the material cylinder | | | 280 to 300 °C |
| Spray nozzle temperature | | | 270 to 290 °C |
| Processing (melt) temperature | | | 280 to 300 °C |
| Temperature | | | 80 to 100 °C |
| Thermal performance | Test Condition | Test Method | Test Result |
|---|
| Heat distortion temperature | | ASTM D648 | 133 °C |
| Heat distortion temperature | | ISO 75-2/Bf | 133 °C |
| Heat distortion temperature | | ASTM D648 | 122 °C |
| Heat distortion temperature | | ISO 75-2/Af | 122 °C |
| vicat | | ISO 306/B50 | 140 °C |
| ball-indentation hardness | | IEC 60695-10-2 | 通过 |
| Linear coefficient of thermal expansion | | ASTM E831 | 7.0E-5 cm/cm/°C |
| Linear coefficient of thermal expansion | | ISO 11359-2 | 7.0E-5 cm/cm/°C |
| thermal conductivity | | ASTM C177 | 0.20 W/m/K |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices